Zebra Stripe Información técnica

Busca en linea o descarga Información técnica para Impresoras De Etiquetas Zebra Stripe. Zebra Stripe Technical information Manual de usuario

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 119
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 0
Maintenance
Manual
Volume 1:
General
Maintenance
Stripe Maintenance Manual
®
Volume 1: General Maintenance
Part # 44868L
Rev. 1
Vista de pagina 0
1 2 3 4 5 6 ... 118 119

Indice de contenidos

Pagina 1 - Stripe Maintenance Manual

MaintenanceManualVolume 1:GeneralMaintenanceStripe Maintenance Manual®Volume 1: General MaintenancePart # 44868LRev. 1

Pagina 2 - WARRANTY INFORMATION

Total media width Maximum 4.5" 115 mmMaximum whenCutter is installed4.0" 101.6 mmMinimum 0.75" 19 mmLabel length Maximum See “Printing

Pagina 3

444594409344329M4421644124PRINTHEAD ASSEMBLY(REF.)442164405444466Toggle and Printhead AssemblyDrawings and Parts Lists Stripe Maintenance Manual: Volu

Pagina 4 - Table of Contents

Page 7-1044868LPRINTER MODEL: STRIPEMedia Sensor and Ribbon GuidesPART NUMBER DESCRIPTION QUANTITY07257 Washer, Flat230466 Washer, Flat244011 Media Gu

Pagina 5

4418907257304664438644397M44397M44140M44140-2M44135M4411444114444664405444011Media Sensor and Ribbon GuidesDrawings and Parts Lists Stripe Maintenance

Pagina 6 - 44868L Page 1-1

Page 7-1244868LPRINTER MODEL: STRIPEDrive SystemPART NUMBER DESCRIPTION QUANTITY44019 Idler Shaft144022 Platen Pulley144023-0M Stepper Motor (S-500) (

Pagina 7 - Page 1-2 44868L

4405544023-0M (S500)44023-1M (S300)44023-2M (S500 Peel)45189-5 (S500 Peel)45189-6 (S500)45189-8 (S300)45189-9 (S500 Peel)44023-6M45189-104401944025440

Pagina 8 - 44868L Page 2-1

Page 7-1444868LPRINTER MODEL: STRIPEPlaten and Power SupplyPART NUMBER DESCRIPTION QUANTITY30260 Washer, Wave .250630261 Washer, Flat .250244004 Power

Pagina 9 - Page 2-2 44868L

4401444004M4411444644M44646M44484440144452344187442824402044013302603026044013Platen and Power SupplyDrawings and Parts Lists Stripe Maintenance Manua

Pagina 10 - (Printhead position may

Page 7-1644868LPRINTER MODEL: STRIPEPrinthead AssemblyPART NUMBER DESCRIPTION QUANTITY01159 Washer, Lock, Star110401 Screw, M3 x .5 x 4510403 Screw, M

Pagina 11

44000M44200M104011040144018A10403441234405444054401934019344940445204410044118440394403201159104033095644125PartA68Dots/mmPrinthead AssemblyDrawings a

Pagina 12 - 44868L Page 2-5

Page 7-1844868LPRINTER MODEL: STRIPEPeel-Off Option Front ViewPART NUMBER REF. DESCRIPTION QUANTITY44191 Ground Chain Assy. (5 1/16")144218 Hook,

Pagina 13 - Page 2-6 44868L

The following bar codes are available on both the Stripe S-300 and S-500 unlessindicated otherwise:The following fonts are standard on the S-300 and S

Pagina 14 - 44868L Page 2-7

ADBCp/o Ap/o Bp/o Dp/o C44463MPART NO.AASSY44349MB44398MC44284MD*44383*44383*441914439144218443464494344942*NOTE: 44191 (Ground Chain) and44383 (Groun

Pagina 15 - Page 2-8 44868L

Page 7-2044868LPRINTER MODEL: STRIPEPeel-Off Option Rear ViewPART NUMBER REF. DESCRIPTION QUANTITY01159 Washer, Lock, Star101882 Screw, 4-40 Phillips4

Pagina 16 - 44868L Page 2-9

PART NO.44536M44496M44488M44487M44275M44292MASSYABCDEFA44023-2M (8-DOT)44023-6M (6-DOT)45189-7 (8-DOT)44491 (6-DOT)BCDEFp/o Ap/o Ap/o Fp/o B4411444665

Pagina 17 - Page 2-10 44868L

Page 7-2244868LPRINTER MODEL: STRIPECutter OptionPART NUMBER DESCRIPTION QUANTITY06223 Cable Clamp107257 Flat Washer110432 Screw, M4X.7 12 Cap110432M

Pagina 18 - 3 Printer Diagnostics

PLUG44674 CABLE ASSYINTO J1244444 DOOR(REF.)ELECTRONICS SIDE VIEW DETAIL44674(REF.)4467444710M44986449451046144437M10432M104320725706223p/o44437Mp/o10

Pagina 19 - Printer Self Tests

Page 7-2444868LDrawings and Parts Lists Stripe Maintenance Manual: Volume 1

Pagina 20 - FEED Key Self Test

AC Power Cable Selection...8-1Cable Requirements...

Pagina 21 - FEED, PAUSE, and CANCEL Keys

American Standard Code for Information Interchange00 NUL 20 space 40 @ 60 ‘01 SOH 21 ! 41 A 61 a02 STX 22 “ 42 B 62 b03 ETX 23 # 43 C 63 c04EOT 24$ 44

Pagina 22 - FEED Key and PAUSE Key

All direct thermal and thermal transfer materials do not have the same PrintDarkness requirements. The best way to check for the proper Print Darkness

Pagina 23 - Extended Printer Diagnostics

1. Load media (and ribbon if required) according to the appropriate MediaLoading and Ribbon Loading Instructions found in the printer’s User Guide.Ins

Pagina 24 - FEED Key Loopback Test

• Serial RS-232 data communication; 110 - 19,200 baud; parity, data bits andXON-XOFF/DTR protocols are all switch-selectable• Parallel Data Communicat

Pagina 25 - Page 3-8 44868L

A DB25-S connector is located at the rear of the Zebra Stripe printer andprovides serial data communications to a host using RS-232 signaling.The pino

Pagina 26 - 44868L Page 3-9

The S-500 printer may have a Parallel Data Communications Port instead of thepreviously mentioned Serial Data Port. The Parallel Interface has a stand

Pagina 27 - Page 3-10 44868L

All of the printer controls and indicatorsare located on the front of the unit,except for the Power ON/OFF Switch,which is located on the left side of

Pagina 28 - Service Diagnostics Tests

printed will be canceled. If there are no formats in the printer, the CANCEL Keyis ignored. If the CANCEL Key is pressed for an extended period of tim

Pagina 30 - 44868L Page 4-1

3 Printer DiagnosticsIn this section... PagePower On Self Test...3-1Printe

Pagina 31 - Page 4-2 44868L

Printer Self TestsThese Self Tests produce sample printouts and provide specific information thathelps determine the operating conditions for the prin

Pagina 32 - 44868L Page 4-3

WARRANTY INFORMATION1. Printer WarrantyZEBRA printers, excluding thermal printheads which are war-ranted separately below, are warranted against defec

Pagina 33 - Page 4-4 44868L

PAUSE Key Self TestS-500 PrinterThis Self Test is made up of fourseparate features, printing at bothspeed “A” (2" per second) andspeed “D” (6&quo

Pagina 34 - 44868L Page 4-5

“Darkness” value specified on the Configuration Printout.The resulting numeric value (0 to 30) is the best darkness value for that specificMedia/Ribbo

Pagina 35 - Page 4-6 44868L

FEED Key and PAUSE KeyPressing these two keys at the same time, while turning the Power ON,temporarily resets the Printer Configuration to the Factory

Pagina 36 - 44868L Page 4-7

PAUSE Key and CANCEL KeyThis self test can be used to verify proper printer operation after parts have beenreplaced or adjusted. When activated, the p

Pagina 37 - Page 4-8 44868L

PAUSE Key Loopback TestThis test demonstrates the media movement capabilities of the printer andprovides a test printout to view while making print qu

Pagina 38 - 44868L Page 4-9

FORMAT PRINTING TEST FUNCTION1 20 at Speed D Left Ribbon Wrinkle2 20 at Speed D Right Ribbon Wrinkle3 20 at Speed D Bar Code Wrinkle Test (Code-39)8 2

Pagina 39 - Page 4-10 44868L

Figure 3.10 Test, Formats 4 and 11Figure 3.8 Test, Formats 2 and 9Figure 3.9 Test, Formats 3 and 10 Stripe Maintenance Manual: Volume 1 Printe

Pagina 40 - 44868L Page 5-1

Figure 3.13 Test, Formats 7 and 14Figure 3.12 Test, Formats 6 and 13Figure 3.11 Test, Formats 5 and 12 Printer Diagnostics Stripe Maintenance

Pagina 41 - Page 5-2 44868L

Service Diagnostics TestsIf a jumper is installed between test points TP1 and TP2 on the main logic boardwhen the power is turned ON, the printer will

Pagina 42 - 44868L Page 5-3

Printer Diagnostics Stripe Maintenance Manual: Volume 1 Page 3-12 44868L

Pagina 43 - Page 5-4 44868L

2. Supplies WarrantyZEBRA supplies are warranted to be free from defects in materialsor workmanship for a period of either the stated material shelf l

Pagina 44 - 44868L Page 5-5

Tools Required ...4-1Cleaning the Printer ...

Pagina 45 - Page 5-6 44868L

Inconsistent print quality, such as voids in the bar code or graphics, may indicatea dirty printhead. For optimum performance, Zebra recommends perfor

Pagina 46 - 44868L Page 5-7

The Cutter Module requires periodic cleaning to remove paper dust and gummedlabel residue. The procedure on the following pages should be performed by

Pagina 47 - Page 5-8 44868L

I. Remove the Cutter Module from the printer.1. Turn the printer’s AC power OFF.2. Remove the Label Catch Tray by lifting it up and away from the fro

Pagina 48 - 44868L Page 5-9

II. Disassemble the Cutter Module.1. Refer to Figure 4.5. Hold the Cutter Module as illustrated. Put your thumbs on the two WireSpring Loops and your

Pagina 49 - Page 5-10 44868L

IV. Reassemble the Cutter Module.1. Refer to Figure 4.6. Position the two Wire Springs down against the Lower Cutter Blade.2. Place the Rear Cutter B

Pagina 51 - Page 5-12 44868L

V. Reinstall the Cutter Module.1. Refer to Figure 4.9. Position the Cutter Module above the Cutter Mounting Posts. Press down onthe Cutter Module unt

Pagina 52 - 44868L Page 5-13

PrintheadSolvent/isopropyl alcohol After every roll of media (or 500feet of fanfold media) whenprinting direct thermal and afterevery roll of ribbon w

Pagina 54 - 44868L Page 5-15

Table of ContentsWarranty Information ...i1 IntroductionDescription ...1-1Scope ...

Pagina 55 - Page 5-16 44868L

Tools Required ...5-2Test Equipment Required ...

Pagina 56 - 44868L Page 5-17

When a problem occurs with the Zebra Stripe Printer, the service technician shouldfirst insure that the unit is being used properly, then exercise it

Pagina 57 - Page 5-18 44868L

5. Press “PAUSE” to resume printing, and check the new setting.6. For further adjustment, repeat steps 2 through 5. (When no furthercorrections are re

Pagina 58 - 44868L Page 5-19

To determine the position and length of the label or ticket stock, the MediaSensor senses either the “web” between labels or a hole or notch in the pr

Pagina 59 - Page 5-20 44868L

NOTE: Make the Media Sensor Sensitivity and Ribbon Sensor Sensitivity Adjustmentsat the same time.1. Remove the Electronics Cover to allow access to

Pagina 60 - 44868L Page 5-21

Sometimes the standard procedure will not work with especially heavy mediabacking material. In this case, the printer fails to calibrate, goes into PA

Pagina 61 - Page 5-22 44868L

The Label Available Sensor functions only when the printer is set to Peel-Offmode. This mode requires that the Peel-Off option be installed in the pri

Pagina 62 - 44868L Page 5-23

CAUTION: The printer electronics are susceptible to static discharge.Wear an anti-static wrist strap and attach it to the printer chassis.1. Turn the

Pagina 63 - Page 5-24 44868L

6. Reload media and ribbon.7. Perform the Printhead Voltage Adjustment found later in this section, thenreturn to Step 8.8. After setting printhead vo

Pagina 64 - 44868L Page 5-25

II. Adjust the print darkness.1. To begin this procedure, printing on the test labels must initially be a lightgray darkness. First, press the MODE k

Pagina 65 - Page 5-26 44868L

Control Panel Circuit Board Replacement ...5-31Main Logic Board Removal ...5-32Main Logic Board Installation ...5-32

Pagina 66 - 44868L Page 5-27

III. Adjust the printhead position.1. If the Cutter Module is used, remove it.Remove the two Phillips head mounting screws that fasten the Tear-Off P

Pagina 67 - Page 5-28 44868L

18. Tighten the two Strip Plate mounting screws and print 40 to 50 labels to insureconsistent print quality.19. If labels are printing properly, press

Pagina 68 - 44868L Page 5-29

These procedures are an alternate method to those described previously andrequire the use of the Printhead Adjustment Screws. See Figure 5.9 to ident

Pagina 69 - Page 5-30 44868L

NOTE: Use a cotton swab moistened with Zebra-recommended Printhead CleaningSolution (part # 1426) to clean the Printhead Element Surface before print

Pagina 70 - 44868L Page 5-31

In the factory, the Stripe printer is aligned and tested using full width,non-continuous media to print thermal transfer labels at Speed C (4"/se

Pagina 71 - Page 5-32 44868L

17. Apply gentle forward pressure with the Head Open Lever against the Printhead Assembly andadjust the Position Adjustment Screws clockwise, until th

Pagina 72 - 44868L Page 5-33

CAUTION: The Screws in the Print Mechanism are of different lengths.Incorrect replacement could damage the Printhead. Segregate the screwsduring disas

Pagina 73 - Page 5-34 44868L

11. Push the Ribbon Cable “G” into the Print Element Assembly “A” connector,making sure that it is fully seated. (Failure to fully seat the connector

Pagina 74 - 44868L Page 5-35

4. Turn the Power OFF and, while pressing the PAUSE Key, turn the Powerback ON to initialize the “Head Alignment” test, or download a format youwish t

Pagina 75 - Page 5-36 44868L

When a Printhead or the printer’s Power Supply is replaced, the PrintheadVoltage must be adjusted for the proper value. This adjustment establishes th

Pagina 76 - 44868L Page 5-37

Description...1-1Scope...

Pagina 77 - Page 5-38 44868L

If printing is too light on one side of the label, or if media with a differentthickness is used, printhead pressure may need to be adjusted in order

Pagina 78 - 44868L Page 5-39

The voltage applied to the printhead is the same voltage applied to the CutterModule. The specific voltage applied to the cutter motor is controlled b

Pagina 80 - 44868L Page 5-41

The Ribbon Strip Plate position can be adjusted to provide proper tracking andseparation of the ribbon from the media after printing. If the ribbon do

Pagina 81 - Page 5-42 44868L

Method 2: For printers that DO have a Dual-Tension Spindle currentlyinstalled. For this method, refer to Figure 5.17.a) Loosen the Screw (10432) at th

Pagina 82 - 44868L Page 6-1

(If your printer is not equipped with a Dual-Tension Ribbon Supply Spindlelike the one shown in Figure 5.17, skip this section.)In the Normal Position

Pagina 83 - Page 6-2 44868L

1. Insure that the printer is OFF and that Media and Ribbon are loaded.2. Remove any used ribbon from the Ribbon Take-up Spindle by pressing thebutton

Pagina 84 - 44868L Page 6-3

This procedure starts on the previous page. The sequence below is to befollowed only if the power leads at the Ribbon Take-Up Motor are connected byr

Pagina 85 - Labels are not

1. To adjust the Backing Rewind Spindle Tension refer to Figure 5.20.2. Turn Printer OFF and remove media and ribbon.3. Tape the end of the Mylar stri

Pagina 86 - 44868L Page 6-5

1. Turn printer OFF and wait for all the front panel lights to turn OFF.2. Remove the power cord, media and ribbon.3. Remove the Electronics Compartme

Pagina 87 - Page 6-6 44868L

Stripe models are illustrated along with their maintenance part numbers. Thoseparts which are specific to a particular model are individually identifi

Pagina 88 - 44868L Page 6-7

1. Refer to the Cover Assembly Drawing in Section 7 and remove the FrontDoor (part # 44076) of the printer.2. Remove the Printer’s Electronics Cover a

Pagina 89 - Page 6-8 44868L

CAUTION: Prior to removing and replacing circuit boards and electricalassemblies, observe proper electrostatic and electrical safety precautions.1. Re

Pagina 90 - 44868L Page 6-9

To replace the EPROMs when installing firmware enhancements, read theinstructions included in the upgrade kit.The Software Kit Number is 44724VXX.xx.

Pagina 92 - 44868L Page 7-1

1. Turn the printer OFF and remove the power cord.2. Remove the media and ribbon.3. Remove the Rear Cover, Front Control Panel Assembly, Media SensorA

Pagina 93 - Page 7-2 44868L

These procedures apply to the Main Drive Belt and the Rewind Spindle Drive Belt.1. Turn the printer OFF and remove the power cord.2. Remove the media

Pagina 94 - Cover Assemblies

1. Refer to the Platen and Power Supply Drawing in Section 7.2. Remove the Rear Cover, Front Control Panel Assembly, Media Assembly,Main Logic Board a

Pagina 95 - Page 7-4

1. Turn the printer OFF and remove the power cord.2. Refer to Ribbon/Media Supply and Drive System drawings in Section 7.3. Remove the Rear Cover, Fro

Pagina 96 - Logic Board and Control Panel

A potentiometer (RV1) is mounted on the printer’s Power Supply Board that willbalance the current traveling to both phases of the stepper motor. Prope

Pagina 97 - Page 7-6

Follow the procedure below for removing the Power Supply. 1. Turn the printer OFF and remove the power cord.2. Remove the Rear Cover, Front Control Pa

Pagina 98 - Ribbon and Media Supply

Printer Specifications...2-2Printing Considerations...

Pagina 99 - Page 7-8

CAUTION: Turn the printer’s AC Power Switch OFF and disconnect theprinter’s AC Power Cable before replacing the Fuse.A User replaceable AC Power Fuse

Pagina 100 - Toggle and Printhead Assembly

One of the Factory Installed Options for the S-500 Printer is the BatteryBacked-Up 256K RAM Memory. The Battery used with this option is a 3 VDCLithiu

Pagina 101 - Page 7-10

Troubleshooting Tables...6-1Sample Labels for Troubleshooting ...

Pagina 102 - 44868L Page 7-11

Printer stops.RIBBON Light andPAUSE Light ON.Ribbon not loaded orincorrectly loaded.Load ribbon correctly. Ribbon Sensor not sensingribbon that is loa

Pagina 103 - Page 7-12

Poor Print Quality. Darkness too low. Increase Print Darkness.Incorrect Media and Ribboncombination.Replace Media or Ribbon.Printhead Adjustments inco

Pagina 104 - Drive System

Misregistration andmisprint of 1 to 3labels.Media was pulled when motorwas not moving.Open and close the printhead so that itcalibrates to find the la

Pagina 105 - Page 7-14

The Cutter is notcutting labels cleanly.Cutter is dirty. Clean Cutter.Cutter blades are dull. Replace Cutter Module.The Cutter isjamming up withlabels

Pagina 106 - Platen and Power Supply

Acceptable Label:• Darkness properly set• Printhead positionedcorrectly• Toggles balanced (equalpressure on left and rightsides)Unacceptable Label:• D

Pagina 107 - Page 7-16

Unacceptable Label:• Darkness very low• Printhead positionedcorrectly• Toggles balanced (equalpressure on left and rightsides)Unacceptable Label:• Dar

Pagina 108 - 44868L Page 7-17

Unacceptable Label:• Darkness properly set• Printhead too far back• Breakup on trailing edgesof bars (opposite thedirection of movement)• Black is spl

Pagina 109 - Page 7-18

Resolution 203.2 dots per inch (8 dots per mm) 152.4 dots per inch (6 dots per mm)Dot size (square) 0.00492" (0.125 mm) 0.00656" (0.167 mm)M

Pagina 110 - 44868L Page 7-19

Unacceptable Label:• Darkness properly set• Printhead position correcton left side, way too farback on right side• Noisy printing (breakupon trailing

Pagina 111 - Page 7-20

If you encounter any problem which cannot be corrected with the aid of thismanual, contact Technical Support immediately to minimize or avoid printerd

Pagina 112 - 44868L Page 7-21

Mechanical Parts and Assemblies ...7-1Cover Assemblies...

Pagina 113 - Page 7-22

44070-0 Main Door—Blank44070-2 Main Door—With logo44075 Rear Cover44076 Front Door (Black w/Zebra and Stripe logos)44076-0 Front Door (White w/no logo

Pagina 114 - 44868L Page 7-23

4411444185M440754407644076-044076-144076-244076-34444444070-044070-2Cover AssembliesDrawings and Parts Lists Stripe Maintenance Manual: Volume 144868L

Pagina 115 - Page 7-24

Page 7-444868LPRINTER MODEL: STRIPELogic Board and Control PanelPART NUMBER DESCRIPTION QUANTITY01155 Washer, Lock201159 Washer, Lock, Star109367 Hex

Pagina 116 - 44868L 8-1

44072-14453744505M440534464944135M(REF.)4409544114441144405340193445404438744716M44717M44718M44719M44721M44670M (44719M + 44135M)CBA011590936701155442

Pagina 117 - 8-2 44868L

Page 7-644868LPRINTER MODEL: STRIPERibbon and Media SupplyPART NUMBER DESCRIPTION QUANTITY10432 Screw, M4130251 Washer, Flat444043M Ribbon Tension Mot

Pagina 118 - 44868L 8-3

4410044046-244043M44198M302513025144066M44067440684406944912M44052M44052-2M44118441144448144084443564417410432Ribbon and Media SupplyDrawings and Part

Pagina 119 - 8-4 44868L

Page 7-844868LPRINTER MODEL: STRIPEToggle and Printhead AssemblyPART NUMBER DESCRIPTION QUANTITY44030 Print Mechanism Assy. (w/o Printhead)144054 Scre

Comentarios a estos manuales

Sin comentarios