Zebra 110Xi4 Guía de usuario Pagina 122
- Pagina / 188
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Routine Maintenance
Cleaning Schedule and Procedures
122
P1009874-003 Xi4™/RXi4™ User Guide 4/30/13
Clean the Snap Plate
Clean the snap plate when label adhesive or a label is stuck to the underside. Figure 20 shows
the location of the snap plate. The snap plate is made of plastic in RFID printers and of metal
in non-RFID printers.
Figure 20 • Snap Plate Location
Non-RFID Printers
To clean a metal snap plate in a non-RFID printer, complete these steps:
1.
2.
Important • Be careful not to bend or twist the metal snap plate as you remove it from or
insert it into the printer.
Caution • Turn off (O) the printer and disconnect it from the power source before
performing the following procedure.
Turn off (O) the printer, and disconnect the AC power cord and all data cables.
Caution • While performing any tasks near an open printhead, remove all rings,
watches, hanging necklaces, identification badges, or other metallic objects that could
touch the printhead.
Open the printhead and remove the media and ribbon (if used).
- User Guide 1
- Part Number: P1009874-003 2
- Declaration of Conformity 3
- Compliance Information 4
- Contents 5
- About This Document 9
- Who Should Use This Document 10
- Bubbledot ICG font 11
- SETUP/EXIT button 12
- CALIBRATE button 12
- Introduction 13
- Printer Components 14
- Control Panel 15
- Printer Setup 17
- Before You Begin 18
- Handling the Printer 19
- Select a Site for the Printer 20
- I) may damage the 21
- Interface 23
- Standard or 23
- Optional 23
- Description 23
- O) position 26
- Power Cord Specifications 27
- Types of Media 29
- Ribbon Overview 31
- Adhesive Test 32
- Ribbon Scratch Test 32
- Operations 33
- Media Paths 35
- Cutter Cutter 36
- Rewind Rewind (without 36
- Cutter option) 36
- Prepare the Media for Loading 37
- 110Xi4/R110Xi4 600 dpi 38
- Fanfold Media 40
- Load Media in Tear-Off Mode 42
- RIBBON OUT error 43
- Load Media in Peel-Off Mode 46
- Load Media in Cutter Mode 53
- Load Media in Rewind Mode 58
- If... Then 65
- Pull out the spindle hook 66
- Load Ribbon 67
- If… Then… 68
- 1) and under the 69
- Remove Used Ribbon 72
- Calibrate the Printer 74
- SENSOR PROFILE 75
- MEDIA AND RIBBON 75
- CALIBRATE 75
- Upper Media Sensor 76
- Lower Media Sensor 79
- Toggle Position Adjustment 80
- Printhead Pressure Adjustment 81
- Setup Mode 84
- Exit Setup Mode 85
- Default Password Value 86
- LIST SETUP 87
- LIST NETWORK 88
- WARNING REPLACE 95
- 3. Do you want to continue? 97
- To print a sensor profile: 98
- LOAD BACKING prompt displays 99
- RELOAD ALL displays 99
- Action/Explanation 100
- Configuration 101
- To change the value shown: 103
- Language/Parameter 103
- Error Condition 107
- Feed Label 107
- To skip these parameters: 108
- IDLE DISPLAY 109
- Routine Maintenance 113
- Replacing Printer Components 114
- Lubrication 114
- CLEAN HEAD NOW appears 115
- CLEAN HEAD NOW 116
- 1) counter-clockwise 117
- Clean the Sensors 119
- Transmissive Media Sensor 120
- Media Out Sensor Location 121
- Clean the Snap Plate 122
- RFID Printers 125
- Clean the Cutter 128
- Replace the Fuse 129
- Troubleshooting 131
- Troubleshooting Checklists 132
- LCD Error Messages 133
- LCD Display/ 134
- Printer Condition 134
- O) the printer 135
- I) the printer 135
- Print Quality Problems 139
- Note • A vertical drift of 141
- Calibration Problems 143
- NONE. See 144
- Ribbon Problems 145
- RFID TAG 146
- MEDIA POWER UP and 147
- O) and then back on (I) too 148
- LANGUAGE 149
- SAVE CHANGES in the 149
- Printer Diagnostics 151
- CANCEL Self Test 152
- PAUSE Self Test 153
- FEED Self Test 154
- Print Quality Description 156
- FEED and PAUSE Self Test 157
- Sensor Profile 159
- Specifications 161
- Features 162
- Bar Codes 163
- General Specifications 164
- Print Specifications by Model 165
- 140Xi4, 170Xi4, and 220Xi4 166
- Ribbon Specifications 167
- Media Specifications 168
- End User License 171
- Agreement 171
- End User License Agreement 172
- Glossary 177
- Numerics 181
Relacionado con productos y manuales para Impresoras De Etiquetas Zebra 110Xi4
Impresoras De Etiquetas Zebra ZT420 Guía de usuario
(192 paginas)
(192 paginas)
Impresoras De Etiquetas Zebra GC420t Guía de usuario
(116 paginas)
(116 paginas)
Impresoras De Etiquetas Zebra ZM400 Guía de usuario
(116 paginas)
(116 paginas)
Impresoras De Etiquetas Zebra ZD500 Guía de usuario
(160 paginas)
(160 paginas)
Impresoras De Etiquetas Zebra ZT230 Guía de usuario
(18 paginas)
(18 paginas)
Impresoras De Etiquetas Zebra GC420d Guía de usuario
(100 paginas)
(100 paginas)
Impresoras De Etiquetas Zebra GX430D Guía de usuario
(128 paginas)
(128 paginas)
Impresoras De Etiquetas Zebra T5206R Manual de usuario
(394 paginas)
(394 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales