Zebra ZT210 Manual de usuario descargar pdf (Pagina 70)

Printer Setup

Load the Media

P1048261-004 8/22/12

17. Feed the liner behind the peel assembly. Make sure that the end of the liner falls outside of

the printer.

18. Complete this step only if you want to use Peel-Off mode with Liner Take-Up. Your

printer must have the Liner Take-Up option installed.

18-a. Slide the liner into the slot in the liner take-up spindle (1).

18-b. Push the liner back until it touches the back plate of the liner take-up spindle

assembly.

1 2 ... 65 66 67 68 69 70 71 72 73 74 75 ... 167 168

ZT210™/ZT220™/ZT230™ 1
User Guide 1
Declaration of Conformity 3
Compliance Information 4
Contents 5
About This Document 9
Who Should Use This Document 10
Contacts 11
Document Conventions 12
Introduction 13
Printer Components 14
Control Panel 15
HOME MENU 18
SETTINGS 18
▼ XXXXXXX ▲ 19
SETTINGS Menu 20
SETTINGS Menu (continued) 21
TOOLS Menu 24
TOOLS Menu (continued) 25
NETWORK Menu 28
NETWORK Menu (continued) 29
LANGUAGE Menu 32
LANGUAGE Menu (continued) 33
SENSORS Menu 34
SENSORS Menu (continued) 35
PORTS Menu 36
PORTS Menu (continued) 37
Types of Media 38
Printer Setup and Operation 39
Ribbon Overview 40
Adhesive Test 41
Ribbon Scratch Test 41
Printer Setup and 43
Operation 43
Handling the Printer 44
I) may damage the 46
Data Cables 48
115 V AC 49
230 V AC 49
Power Cord Specifications 50
Select a Print Mode 52
Load the Ribbon 55
Printer Setup 56
Load the Media 60
Roll Media 61
Fanfold Media 61
Roll Media (Continued) 62
Fanfold Media (Continued) 62
If using… Then… 64
Liner Take-Up) on page 68 65
Mode on page 74 65
Final Steps for Tear-Off Mode 66
11. Close the media door 67
23. Close the media door 73
Final Steps for Cutter Mode 74
30. Close the media door 76
Printer Configuration 77
Changing Printer Settings 78
Print Settings 79
• THERMAL TRANS 80
• DIRECT THERMAL 80
• TEAR OFF 81
• CUTTER 81
Print Listings on Label 83
Important • 87
Directory Listing 88
Network Settings 89
Print Server Settings > 91
Factory Print Server Settings 91
Language Settings 92
• ZPL II 94
Sensor Settings 95
Port Settings 96
Serial Communications Setup 97
MEDIA/RIBBON CAL 98
LOAD BACKING 99
REMOVE RIBBON 99
Remove the ribbon (if used) 100
CALIBRATING 101
PLEASE WAIT 101
RELOAD ALL 101
CONTINUE 101
Close the printhead 102
Close the media door 102
Reload the ribbon (if used) 102
Adjust the Printhead Pressure 103
If the media... Then 104
Adjust Ribbon Tension 106
Remove Used Ribbon 107
Routine Maintenance 109
Area Method Interval 110
Printer Exterior 111
Media Compartment and Sensors 111
Raise the media door 113
8. Close the media door 115
Clean the Peel Assembly 116
Clean the Cutter Module 120
Remove the cutter shield 121
Replacing Printer Components 124
Lubrication 124
Troubleshooting 125
Troubleshooting Checklist 126
Meaning of Indicator Lights 127
Printing Issues 129
Ribbon Problems 132
Error Messages 134
RIBBON OUT 135
PH NOT AUTHENTICATED 135
REPLACE PRINTHEAD 135
Display/ 137
Indicator Lights 137
Communications Problems 138
Miscellaneous Issues 139
Printer Diagnostics 141
CANCEL Self Test 142
PAUSE Self Test 143
FEED Self Test 144
Print Quality Description 145
FEED + PAUSE Self Test 147
CANCEL + PAUSE Self Test 147
FE indicates a framing error 148
PE indicates a parity error 148
NE indicates noise 148
Sensor Profile 149
Specifications 151
General Specifications 152
Printing Specifications 153
Ribbon Specifications 153
Media Specifications 154
Glossary 155
8/22/12 P1048261-004 159
P1048261-004 8/22/12 160
8/22/12 P1048261-004 161

Comentarios a estos manuales

Sin comentarios

Zebra ZT210 Manual de usuario Pagina 70

Comentarios a estos manuales

Relacionado con productos y manuales para Impresoras De Etiquetas Zebra ZT210