Zebra 105SL Plus Guía de usuario descargar pdf (Pagina 61)

Operations

Load Media in Rewind Mode

6/30/06 105SL User Guide 11342L-001 Rev. A

9. Extend approximately 36 in. (920 mm) of media out of the printer. Remove and discard

the labels from this exposed media.

10. Remove the hook from the rewind spindle. Store the hook in the bottom of the printer.

11. Slide an empty 3-in. (76.2-mm) core onto the rewind spindle until it is flush against the

guide plate.

1 2 ... 56 57 58 59 60 61 62 63 64 65 66 ... 173 174

User Guide 1
Declaration of Conformity 3
Compliance Information 4
Contents 5
Who Should Use This Document 10
Contacts 11
Document Conventions 12
SETUP/EXIT button 13
About This Document 14
Introduction 15
External View 16
Control Panel 17
Control Panel LCD 18
Control Panel Buttons 18
Control Panel Lights 19
Printer Media Compartment 21
Printer Setup 23
Before You Begin 24
Handling the Printer 25
Select a Site for the Printer 26
Connector Locations 27
Types of Connections 28
Data Cable Requirements 30
4. Turn on (I) the printer 31
Power Cord Specifications 32
Types of Media 33
Ribbon Overview 35
Adhesive Test 36
Ribbon Scratch Test 36
Operations 37
Media Loading Overview 38
Insert Media into the Printer 39
Fanfold Media 40
If… Then… 41
Load Media in Tear-Off Mode 42
Load Media in Peel-Off Mode 46
If the printer has 47
1). Insert the long end 51
If... Then 55
Pull out the spindle hook 56
Load Media in Rewind Mode 57
1) and the adjustable hook 58
2) point down 58
Load Media in Cutter Mode 65
Load Ribbon 69
Remove Used Ribbon 73
Adjust Media Sensors 74
Lower Media Sensor 75
Adjust Printhead Balance 76
Printhead Pressure Adjustment 78
Calibrate the Printer 79
Setup Mode 82
Exit Setup Mode 83
Default Password Value 84
Print a Configuration Label 85
LIST NETWORK 86
TEAR OFF +000 88
- + 88
PRINT MODE 88
-TEAR-OFF + 88
Action/Explanation 89
PRINT WIDTH 90
- MM + 90
MAXIMUM LENGTH 91
-39.0 IN 988 MM 91
To format a memory card: 93
To initialize Flash memory: 94
SENSOR PROFILE 95
PRINT 95
To change the value shown: 100
Parameter 100
LEFT POSITION 102
- ±0000 + 102
HEAD RESISTOR 103
- 0500 OHMS + 103
To skip these parameters: 104
Print Server LCD Displays 106
^WE ZPL command to set 108
PLUS (+) to select YES 109
Parameter Action/Explanation 109
Configuration 110
Control Panel Parameters 110
PC and Memory Cards 111
PCMCIA PC Cards 112
PAUSE light flashes 113
PAUSE light flashes only 113
Routine Maintenance 115
Lubrication 116
Cleaning Schedule 116
Clean the Exterior 117
Take-label sensors 121
Black mark sensor 121
Ribbon sensor 121
Clean the Snap Plate 122
Clean the Cutter 123
Replace the Fuse 124
Troubleshooting 125
Troubleshooting Checklists 126
LCD Error Messages 127
LCD Display/ 128
Printer Condition 128
HEAD COLD 129
OUT OF MEMORY 129
(function) 129
Print Quality Problems 130
Note • A vertical drift of 132
Calibration Problems 133
Communications Problems 134
Ribbon Problems 135
LANGUAGE 136
SAVE CHANGES in the 136
Calibrate 137
Printer Diagnostics 138
CANCEL Self Test 139
PAUSE Self Test 141
FEED Self Test 142
Print Quality Description 144
FEED and PAUSE Self Test 146
Sensor Profile 148
Specifications 149
General Specifications 150
Communications Specifications 151
Other Standard Features 151
Additional Options 151
Agency Approvals 152
Printing Specifications 153
Ribbon Specifications 153
Media Specifications 154
Bar Codes 155
Glossary 157
End User License 161
Agreement 161
End User License Agreement 162
HEAD COLD message, 121 168
HEAD TOO HOT message, 120 168
OUT OF MEMORY message, 121 169
PAPER OUT message, 120 170
RIBBON IN message, 120 171
RIBBON OUT message, 119 171

Comentarios a estos manuales

Sin comentarios

Zebra 105SL Plus Guía de usuario Pagina 61

Comentarios a estos manuales

Relacionado con productos y manuales para Impresión y escaneo Zebra 105SL Plus