Zebra RZ400 Guía de usuario Pagina 144
- Pagina / 156
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Specifications
Printing Specifications
144
79695L-002 Rev. A Z Series
®
/RZ™ Series User Guide 6/6/08
Programmable
constant print
speeds
203 dots/in. • 2.4 in. (61 mm) per second
• 3 in. through 10 in. per second in
1-in. increments (76 mm through
254 mm per second in 25-mm
increments)
• 2.4 in. (61 mm) per second
• 3 in. through 10 in. per second in
1-in. increments (76 mm through
254 mm per second in 25-mm
increments)
300 dots/in. • 2.4 in. (61 mm) per second
• 3 in. through 8 in. per second in
1-in. increments (76 mm through
203 mm per second in 25-mm
increments)
• 2.4 in. (61 mm) per second
• 3 in. through 8 in. per second in
1-in. increments (76 mm through
203 mm per second in 25-mm
increments)
600 dots/in. • 1.5 in (38 mm)
• 2 in. through 4 in. per second in
1-in. increments (51 mm through
102 mm per second in 25-mm
increments)
N/A
Thin film printhead with E
3®
Element Energy Control
Printing Specifications ZM400/RZ400 ZM600/RZ600
- Z Series 1
- /RZ™ Series 1
- User Guide 1
- Declaration of Conformity 3
- Compliance Information 4
- Contents 5
- Section Description 10
- Contacts 11
- Document Conventions 12
- FEED button 13
- CANCEL button 13
- About This Document 14
- Introduction 15
- External View 16
- Printer Media Compartment 18
- Control Panel 19
- Control Panel Buttons 20
- Control Panel Lights 21
- Printer Language Modes 22
- Printer Setup 23
- Before You Begin 24
- Temperature Relative Humidity 25
- Select a Site for the Printer 26
- Interface 27
- Standard or 27
- Optional on 27
- Characteristics 27
- ) may damage the 28
- O) position 31
- Power Cord Specifications 32
- Types of Media 33
- Ribbon Overview 35
- If the ribbon... Then 36
- Operations 37
- Print Mode Printer Option 39
- Load Media 41
- Roll Media 42
- Fanfold Media 42
- Roll Media (Continued) 43
- Fanfold Media (Continued) 43
- PAUSE to enable printing 44
- Close the printhead assembly 54
- Ribbon Coated Outside 55
- (black ribbon spindle) 55
- Ribbon Coated Inside 55
- (gray ribbon spindle) 55
- Load Ribbon 56
- Remove Used Ribbon 59
- Calibrate the Printer 60
- Adjust Printhead Pressure 61
- Media Width 62
- If the media... Then 62
- Configuration 63
- Setup Mode 64
- Exit Setup Mode 65
- Default Password Value 66
- Print a Configuration Label 67
- LIST NETWORK 68
- Language/Parameter 69
- To change the value shown: 69
- Action/Explanation 70
- WARNING REPLACE 77
- To print this label: 79
- To initialize Flash memory: 82
- To print a sensor profile: 82
- LOAD BACKING prompt displays 83
- RELOAD ALL displays 83
- IDLE DISPLAY 93
- RFID Control Panel Parameters 96
- To calibrate an RFID tag: 97
- RFID WRITE PWR 98
- RFID ERR STATUS 98
- RFID TAG TYPE 98
- 1122334455667788 for 2 99
- RFID TAG DATA 99
- RFID Operation 100
- Routine Maintenance 101
- Replacing Printer Components 102
- Lubrication 102
- Area Method Interval 103
- Cleaning Procedures 104
- Clean the Cutter Module 108
- I) the printer 109
- Troubleshooting 113
- Troubleshooting Checklists 114
- LCD Error Messages 115
- O) the printer 116
- HEAD COLD 117
- HEAD TOO HOT 117
- DEFRAGMENTING 118
- ERROR CONDITION 118
- CUTTER JAM 118
- OUT OF MEMORY 118
- (function) 118
- Print Quality Problems 119
- Note • A vertical drift of 121
- Calibration Problems 122
- NONE. See 123
- Ribbon Problems 124
- RFID TAG 125
- MEDIA POWER UP and 126
- RFID Problems 127
- LANGUAGE 128
- SAVE CHANGES in the 128
- O) and then on (I) 129
- CANCEL self tests 131
- CANCEL Self Test 132
- PAUSE Self Test 133
- FEED Self Test 134
- Printer Diagnostics 135
- Print Quality Description 136
- FEED and PAUSE Self Test 137
- RIBBON (2). If 139
- MEDIA (3) for the media 139
- Specifications 141
- General Specifications 142
- Printing Specifications 143
- Media Specifications 145
- Ribbon Specifications 146
- Printer Options 147
- 6/6/08 Z Series 149
- Cutter Jam message, 118 150
- HEAD COLD message 151
- HEAD ELEMENT BAD message, 116 151
- HEAD TOO HOT message, 117 151
- INVALID HEAD message, 115 151
- OUT OF MEMORY message, 118 152
- PAPER OUT message, 116 152
- RIBBON IN message, 116 153
- RIBBON OUT message, 115 153
- THERMISTOR FAULT message 154
- © 2008 ZIH Corp 156
Relacionado con productos y manuales para Impresión y escaneo Zebra RZ400
Impresión y escaneo Zebra QLn420 Manual de usuario
(24 paginas)
(24 paginas)
Impresión y escaneo Zebra TLP 3844-Z Guía de usuario
(68 paginas)
(68 paginas)
Impresión y escaneo Zebra EM 220 Especificaciones
(53 paginas)
(53 paginas)
Impresión y escaneo Zebra GK420d Guía de usuario
(102 paginas)
(102 paginas)
Impresión y escaneo Zebra QL Guía de usuario
(56 paginas)
(56 paginas)
Impresión y escaneo Zebra TTP2130 Especificaciones
(132 paginas)
(132 paginas)
Impresión y escaneo Zebra KR403 Especificaciones
(158 paginas)
(158 paginas)
Impresión y escaneo Zebra EPL2 Manual de usuario
(82 paginas)
(82 paginas)
Impresión y escaneo Zebra R402 Guía de usuario
(72 paginas)
(72 paginas)
Impresión y escaneo Zebra R-140 Guía de usuario
(126 paginas)
(126 paginas)
Impresión y escaneo Zebra GX430D Manual de usuario
(20 paginas)
(20 paginas)
Impresión y escaneo Zebra 243 Guía de usuario
(53 paginas)
(53 paginas)
Impresión y escaneo Zebra P110 Manual de usuario
(60 paginas)
(60 paginas)
Impresión y escaneo Zebra Z6M Especificaciones
(168 paginas)
(168 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales