Zebra 10/100 Guía de usuario Pagina 76
- Pagina / 162
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Getting Started
Defaulting ALL Print Servers
76
P1043301-002 02/28/2012
Defaulting the Print Servers on the HC100 Printers
To default the print server to factory settings, complete these steps:
1. Press and hold Feed for two seconds.
2. Wait for the three blink sequence of the Error/Status LED.
3. Release Feed.
Defaulting the Print Servers on the 105SL, PAX4, Xi4, and ZE500
Printers
To default the print server to factory settings, complete these steps:
1. From the control panel, press Setup/Exit two times.
2. Press Plus (+) five times.
The control panel will read DEFAULT NET.
3. Press Next/Save to save the change.
The control panel will read PRINTER READY.
Note • Be sure to count the number of LED blinks. The three blink sequence defaults only
the print server parameters while the four blink sequence defaults all of the printer
parameters.
- ZebraNet 1
- User Guide 1
- Contents 3
- Who Should Use This Document 8
- Section Description 9
- Contacts 10
- Document Conventions 11
- About This Document 12
- Related Documents 13
- Introduction 15
- Browser Support 16
- Supported Services 16
- Technologies 17
- Supported Security Types 18
- ZebraNet n Print Server 20
- Printer Requirements 22
- Printers 23
- Memory Requirements 24
- If you have… Then… 25
- PN XXXXX 26
- Firmware — Wireless 27
- Compatibility 28
- Specifications 28
- General Specifications 29
- Installation 31
- Before You Begin 32
- Illustration 33
- Installation Instructions 34
- Wireless Radio Card 35
- 5. Turn on (I) the printer 36
- 6. Turn on (I) the printer 38
- Getting Started 39
- Contents (Continued) 40
- Default User ID and Password 41
- 10/100 Print Server 42
- DPI Inches MM 44
- PRINT OUT NETWORK (for 45
- PRINT OUT 45
- SETTINGS 45
- ZT210, ZT220, and ZT230 47
- LP/TLP 2824 Plus Printers 47
- Status Indicator Meaning 50
- SIGNAL STRENGTH and 51
- SIGNAL QUALITY 51
- Wireless Status 52
- Indicator 52
- Status Indicator 54
- Active Device Selection 56
- IP RESOLUTION 59
- Static Route 60
- Gleaning 61
- ZebraLink Alerts 62
- Using ZebraNet Bridge 63
- Using WebView 64
- Add Alert Message 65
- Print Server Settings 68
- Figure 17 • Access Settings 69
- Enabled Protocols 72
- Using a ZPL Command 74
- PAX4 and External Devices 74
- DEFAULT NET 75
- O) the printer 77
- Defaulting ALL Print Servers 78
- Printing Queues 79
- Configuring the Print Queue 80
- Prerequisites 81
- UNIX Configuration 81
- System V Queue Installation 82
- Using Printing Protocols 83
- 1. Open a browser 84
- 12.3.4.123, you would 85
- Home Page 88
- Open a Web browser 89
- The Printer Home Page opens 89
- Figure 20 • Printer Home Page 89
- View Printer Configuration 90
- If... Then 91
- Home link 91
- Print Label 91
- General Setup 93
- Serial Communications Setup 93
- Network Communications 94
- Print Listings on Label 94
- RFID Setup 95
- (RFID Printers/Print Engines 95
- Media Setup 96
- Calibration 96
- ZPL Control 97
- Advanced Setup 97
- 3. Click Submit Changes 98
- 4. Click on the statement 98
- SMTP TCP/IP 100
- X60.15.x and ZSPx 100
- ZebraLink WebView 101
- Directory Listing 103
- Figure 24 • Directory Listing 104
- Button Function/Operation 106
- Printer Controls 108
- Print Server 109
- Web Pages 109
- Status and Configuration 110
- Print Server Settings 111
- Print Server Web Pages 113
- Print Server Features 113
- Use this feature to set the 114
- Use this 114
- Print Server Status 118
- View Port Status 119
- Reset Print Server 120
- Submit Changes 121
- Control Panel 123
- Control Panel Menu Options 124
- Hardware Troubleshooting 129
- Resetting to Factory Defaults 130
- Indicators 130
- Important • Cables with a 131
- (O), wait 10 132
- Defaults 133
- Status LED State Description 134
- LED State Description 134
- Ping the Printer 136
- Start > Run 137
- Open text box, type: cmd 137
- Unable to Configure Device 138
- Wireless Error Messages 138
- General Wireless Issues 139
- • United States 140
- • Canada 140
- IP Issues 142
- Frequently Asked Questions 143
- Glossary 147
- 02/28/2012 P1043301-002 153
- P1043301-002 02/28/2012 154
- NO CARD INSERTED message 138 155
- NOT ASSOCIATED message 138 156
- NOT AUTHENTICATD message 138 156
- 02/28/2012 P1043301-002 159
Relacionado con productos y manuales para Los servidores de impresión Zebra 10/100
(94 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.033 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales