Zebra RZ400 Guía de usuario Pagina 42
- Pagina / 156
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Operations
Load Media
42
79695L-002 Rev. A Z Series
®
/RZ™ Series User Guide 6/6/08
3. Insert media into the printer. Follow the instructions for roll or fanfold media, as
appropriate.
Roll Media
Fanfold Media
a. Remove and discard any tags or
labels that are dirty or that are held
by adhesives or tape.
a. Flip down the media supply guide.
b. Flip down the media supply guide. b. Feed the media through the rear or
bottom access slot.
Rear Feed
Bottom Feed
c. Place the roll of media on the media
supply hanger. Push the roll as far
back as it will go.
d. Flip up the media supply guide. c. Drape the media over the media
supply hanger.
- Z Series 1
- /RZ™ Series 1
- User Guide 1
- Declaration of Conformity 3
- Compliance Information 4
- Contents 5
- Section Description 10
- Contacts 11
- Document Conventions 12
- FEED button 13
- CANCEL button 13
- About This Document 14
- Introduction 15
- External View 16
- Printer Media Compartment 18
- Control Panel 19
- Control Panel Buttons 20
- Control Panel Lights 21
- Printer Language Modes 22
- Printer Setup 23
- Before You Begin 24
- Temperature Relative Humidity 25
- Select a Site for the Printer 26
- Interface 27
- Standard or 27
- Optional on 27
- Characteristics 27
- ) may damage the 28
- O) position 31
- Power Cord Specifications 32
- Types of Media 33
- Ribbon Overview 35
- If the ribbon... Then 36
- Operations 37
- Print Mode Printer Option 39
- Load Media 41
- Roll Media 42
- Fanfold Media 42
- Roll Media (Continued) 43
- Fanfold Media (Continued) 43
- PAUSE to enable printing 44
- Close the printhead assembly 54
- Ribbon Coated Outside 55
- (black ribbon spindle) 55
- Ribbon Coated Inside 55
- (gray ribbon spindle) 55
- Load Ribbon 56
- Remove Used Ribbon 59
- Calibrate the Printer 60
- Adjust Printhead Pressure 61
- Media Width 62
- If the media... Then 62
- Configuration 63
- Setup Mode 64
- Exit Setup Mode 65
- Default Password Value 66
- Print a Configuration Label 67
- LIST NETWORK 68
- Language/Parameter 69
- To change the value shown: 69
- Action/Explanation 70
- WARNING REPLACE 77
- To print this label: 79
- To initialize Flash memory: 82
- To print a sensor profile: 82
- LOAD BACKING prompt displays 83
- RELOAD ALL displays 83
- IDLE DISPLAY 93
- RFID Control Panel Parameters 96
- To calibrate an RFID tag: 97
- RFID WRITE PWR 98
- RFID ERR STATUS 98
- RFID TAG TYPE 98
- 1122334455667788 for 2 99
- RFID TAG DATA 99
- RFID Operation 100
- Routine Maintenance 101
- Replacing Printer Components 102
- Lubrication 102
- Area Method Interval 103
- Cleaning Procedures 104
- Clean the Cutter Module 108
- I) the printer 109
- Troubleshooting 113
- Troubleshooting Checklists 114
- LCD Error Messages 115
- O) the printer 116
- HEAD COLD 117
- HEAD TOO HOT 117
- DEFRAGMENTING 118
- ERROR CONDITION 118
- CUTTER JAM 118
- OUT OF MEMORY 118
- (function) 118
- Print Quality Problems 119
- Note • A vertical drift of 121
- Calibration Problems 122
- NONE. See 123
- Ribbon Problems 124
- RFID TAG 125
- MEDIA POWER UP and 126
- RFID Problems 127
- LANGUAGE 128
- SAVE CHANGES in the 128
- O) and then on (I) 129
- CANCEL self tests 131
- CANCEL Self Test 132
- PAUSE Self Test 133
- FEED Self Test 134
- Printer Diagnostics 135
- Print Quality Description 136
- FEED and PAUSE Self Test 137
- RIBBON (2). If 139
- MEDIA (3) for the media 139
- Specifications 141
- General Specifications 142
- Printing Specifications 143
- Media Specifications 145
- Ribbon Specifications 146
- Printer Options 147
- 6/6/08 Z Series 149
- Cutter Jam message, 118 150
- HEAD COLD message 151
- HEAD ELEMENT BAD message, 116 151
- HEAD TOO HOT message, 117 151
- INVALID HEAD message, 115 151
- OUT OF MEMORY message, 118 152
- PAPER OUT message, 116 152
- RIBBON IN message, 116 153
- RIBBON OUT message, 115 153
- THERMISTOR FAULT message 154
- © 2008 ZIH Corp 156
Relacionado con productos y manuales para Impresión y escaneo Zebra RZ400
Impresión y escaneo Zebra QLn420 Manual de usuario
(24 paginas)
(24 paginas)
Impresión y escaneo Zebra TLP 3844-Z Guía de usuario
(68 paginas)
(68 paginas)
Impresión y escaneo Zebra EM 220 Especificaciones
(53 paginas)
(53 paginas)
Impresión y escaneo Zebra GK420d Guía de usuario
(102 paginas)
(102 paginas)
Impresión y escaneo Zebra QL Guía de usuario
(56 paginas)
(56 paginas)
Impresión y escaneo Zebra TTP2130 Especificaciones
(132 paginas)
(132 paginas)
Impresión y escaneo Zebra KR403 Especificaciones
(158 paginas)
(158 paginas)
Impresión y escaneo Zebra EPL2 Manual de usuario
(82 paginas)
(82 paginas)
Impresión y escaneo Zebra R402 Guía de usuario
(72 paginas)
(72 paginas)
Impresión y escaneo Zebra R-140 Guía de usuario
(126 paginas)
(126 paginas)
Impresión y escaneo Zebra GX430D Manual de usuario
(20 paginas)
(20 paginas)
Impresión y escaneo Zebra 243 Guía de usuario
(53 paginas)
(53 paginas)
Impresión y escaneo Zebra P110 Manual de usuario
(60 paginas)
(60 paginas)
Impresión y escaneo Zebra Z6M Especificaciones
(168 paginas)
(168 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.484 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales