Zebra 170PAX4 Guía de usuario Pagina 29
- Pagina / 156
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Getting Started
Select a Communication Interface
57516L-001 Rev. 1 10/12/2004 170PAX4 User Guide 23
Select a Communication Interface
The way that you connect your print engine to a data source depends on the communication
options installed in the print engine. See Data Ports on page 115 for control signal
descriptions and other additional information.
Standard Connections
Refer to Figure 13. The print engine comes standard with both an Electronics Industries
Association (EIA) RS-232 serial interface (DB-9 connector) and an IEEE 1284 bi-directional
parallel interface. You may use either of these interface methods to send commands and label
formats from a host to the print engine.
Figure 13 • Cable Connections
Caution • Connecting a data communications cable while the power is ON may damage
the print engine.
Note • You must supply all interface cables for your application. Refer to Data Cable
Requirements on page 25 for specific cable requirements.
1
DB-15 applicator interface port
2
Parallel interface connector
3
DB-9 serial interface connector
L
e
ft
-
H
an
dRi
g
ht
-
H
an
d
1
3
2
2
3
1
- User Guide 1
- Contents 3
- Who Should Use This Document 8
- Contacts 9
- Document Conventions 10
- Related Documents 11
- About This Document 12
- Print Engine Basics 13
- Print Engine Exterior View 14
- Front Panel 15
- Button Description/Function 16
- Power On/Off Switch 17
- Getting Started 19
- Before You Begin 20
- Report Shipping Damage 21
- Store the Print Engine 21
- Shipping 21
- Print Engine Installation 22
- Power Cord Specifications 28
- Standard Connections 29
- Optional Print Servers 30
- System Considerations 30
- Interface Considerations 30
- Data Cable Requirements 31
- Types of Media 32
- When to Use Ribbon 34
- Coated Side of Ribbon 34
- Adhesive Test 35
- Ribbon Scratch Test 35
- Print Engine Operation 37
- Load Media 38
- Figure 18 • Loaded Media 39
- 2. Open the media door 40
- Brass thumb nut 41
- Outer media guide 41
- Printhead latch 42
- Locking pin 42
- 16. Close the media door 45
- Load Ribbon 46
- Figure 29 • Loaded Ribbon 47
- 9. Close the media door 50
- Remove Used Ribbon 51
- Calibrate the Print Engine 52
- SENSOR PROFILE 53
- MEDIA AND RIBBON 53
- CALIBRATE 53
- Adjust Media Sensors 54
- Transmissive media sensor 55
- Adjustment knob 55
- Print Engine Configuration 57
- Overview 58
- Exit Setup Mode 59
- LIST SETUP 60
- LIST NETWORK 61
- Default Password Value 62
- Front Panel LCD 63
- Parameter Action/Explanation 64
- MAXIMUM LENGTH 66
- -39.0 IN 988 MM 66
- 3. Do you wish to continue? 69
- 2. Do you wish to continue? 69
- PRINT 70
- FEED to cause 75
- HEAD RESISTOR 77
- - 0500 OHMS + 77
- APPLICATOR PORT 77
- - OFF + 77
- IDLE DISPLAY 81
- RTC TIME 81
- - 14:55 + 81
- LANGUAGE 81
- ZebraNet 82
- Print Server LCD Displays 82
- Routine Maintenance 85
- CLEAN HEAD NOW appears 86
- Clean Interior 87
- Door-open sensor 88
- Ribbon sensor 88
- Toggle Positioning 91
- 7/16 inch 92
- Power Fuse Replacement 93
- Troubleshooting Checklists 96
- LCD Error Messages 97
- HEAD TOO HOT 98
- Memory Errors 99
- Print Quality Problems 100
- Troubleshooting 101
- Communications Problems 103
- Print Engine Diagnostics 106
- CANCEL Self Test 107
- PAUSE Self Test 108
- FEED Self Test 109
- FEED Key and PAUSE Key 110
- Parameter Controlled By 111
- Print Engine Specifications 113
- General Specifications 114
- Electrical Specifications 115
- Communications Specifications 115
- Bar Codes 116
- Printing Specifications 117
- Media Specifications 118
- Ribbon Specifications 119
- Data Ports 121
- Parallel Port 122
- Serial Port 123
- Serial Pin Configuration 124
- RS-232 Interface Connections 125
- DB-9 to DB-25 Connections 126
- Modem Connection 127
- Pin No. Non-Isolated Isolated 130
- Proprietary Statement 133
- Liability Disclaimer 134
- Limitation of Liability 134
- Warranty Information 135
- Related Hardware Items 136
- Supplies Products 136
- Repair Services 137
- Printer Software 139
- License Agreement 139
- 3. RESTRICTIONS 140
- Glossary 145
- HEAD COLD 150
- ZPL mode setting, 69 154
- Zebra support, 3 154
- Customer Order # 57516L-001 156
- © 2004 ZIH Corp 156
Relacionado con productos y manuales para Impresoras De Etiquetas Zebra 170PAX4
Impresoras De Etiquetas Zebra Stripe Guía de usuario
(78 paginas)
(78 paginas)
(20 paginas)
Impresoras De Etiquetas Zebra S600 Especificaciones
(94 paginas)
(94 paginas)
Impresoras De Etiquetas Zebra S600 Especificaciones
(168 paginas)
(168 paginas)
Impresoras De Etiquetas Zebra Stripe Información técnica
(119 paginas)
(119 paginas)
Impresoras De Etiquetas Zebra T402 Guía de usuario
(60 paginas)
(60 paginas)
Impresoras De Etiquetas Zebra DA402 Guía de usuario
(56 paginas)
(56 paginas)
Impresoras De Etiquetas Zebra A300 Especificaciones
(396 paginas)
(396 paginas)
Impresoras De Etiquetas Zebra 2684 Manual de usuario
(60 paginas)
(60 paginas)
Impresoras De Etiquetas Zebra RP4T Especificaciones
(49 paginas)
(49 paginas)
Impresoras De Etiquetas Zebra Stripe Guía de usuario
(150 paginas)
(150 paginas)
Impresoras De Etiquetas Zebra S400 Guía de usuario
(146 paginas)
(146 paginas)
Impresoras De Etiquetas Zebra TTPM2 Especificaciones
(102 paginas)
(102 paginas)
Strong Pools and Spas podręczniki
Wykaz produktów Strong Pools and Spas zawiera 23 instrukcje obsługi i przewodniki dla 16 modeli w 4 typu urządzeń
Comentarios a estos manuales