Zebra 170PAX4 Guía de usuario descargar pdf (Pagina 40)

34 170PAX 4 User Guide 10/12/2004 57516L-001 Rev. 1

Print Engine Operation

Load Media

To load media, complete these steps:

1. Load media on the media supply reel of the applicator (refer to the applicator’s user

guide).

2. Open the media door.

3. See Figure 19. Press down on the pinch roller release latch.

The pinch roller assembly springs up (Figure 20).

Figure 19 • Pressing the Pinch Roller Release Latch

Figure 20 • Opened Pinch Roller Assembly

Pinch roller release latch

Pinch roller assembly

1 2 ... 35 36 37 38 39 40 41 42 43 44 45 ... 155 156

User Guide 1
Contents 3
Who Should Use This Document 8
Contacts 9
Document Conventions 10
Related Documents 11
About This Document 12
Print Engine Basics 13
Print Engine Exterior View 14
Front Panel 15
Button Description/Function 16
Power On/Off Switch 17
Getting Started 19
Before You Begin 20
Report Shipping Damage 21
Store the Print Engine 21
Shipping 21
Print Engine Installation 22
Power Cord Specifications 28
Standard Connections 29
Optional Print Servers 30
System Considerations 30
Interface Considerations 30
Data Cable Requirements 31
Types of Media 32
When to Use Ribbon 34
Coated Side of Ribbon 34
Adhesive Test 35
Ribbon Scratch Test 35
Print Engine Operation 37
Load Media 38
Figure 18 • Loaded Media 39
2. Open the media door 40
Brass thumb nut 41
Outer media guide 41
Printhead latch 42
Locking pin 42
16. Close the media door 45
Load Ribbon 46
Figure 29 • Loaded Ribbon 47
9. Close the media door 50
Remove Used Ribbon 51
Calibrate the Print Engine 52
SENSOR PROFILE 53
MEDIA AND RIBBON 53
CALIBRATE 53
Adjust Media Sensors 54
Transmissive media sensor 55
Adjustment knob 55
Print Engine Configuration 57
Overview 58
Exit Setup Mode 59
LIST SETUP 60
LIST NETWORK 61
Default Password Value 62
Front Panel LCD 63
Parameter Action/Explanation 64
MAXIMUM LENGTH 66
-39.0 IN 988 MM 66
3. Do you wish to continue? 69
2. Do you wish to continue? 69
PRINT 70
FEED to cause 75
HEAD RESISTOR 77
- 0500 OHMS + 77
APPLICATOR PORT 77
- OFF + 77
IDLE DISPLAY 81
RTC TIME 81
- 14:55 + 81
LANGUAGE 81
ZebraNet 82
Print Server LCD Displays 82
Routine Maintenance 85
CLEAN HEAD NOW appears 86
Clean Interior 87
Door-open sensor 88
Ribbon sensor 88
Toggle Positioning 91
7/16 inch 92
Power Fuse Replacement 93
Troubleshooting Checklists 96
LCD Error Messages 97
HEAD TOO HOT 98
Memory Errors 99
Print Quality Problems 100
Troubleshooting 101
Communications Problems 103
Print Engine Diagnostics 106
CANCEL Self Test 107
PAUSE Self Test 108
FEED Self Test 109
FEED Key and PAUSE Key 110
Parameter Controlled By 111
Print Engine Specifications 113
General Specifications 114
Electrical Specifications 115
Communications Specifications 115
Bar Codes 116
Printing Specifications 117
Media Specifications 118
Ribbon Specifications 119
Data Ports 121
Parallel Port 122
Serial Port 123
Serial Pin Configuration 124
RS-232 Interface Connections 125
DB-9 to DB-25 Connections 126
Modem Connection 127
Pin No. Non-Isolated Isolated 130
Proprietary Statement 133
Liability Disclaimer 134
Limitation of Liability 134
Warranty Information 135
Related Hardware Items 136
Supplies Products 136
Repair Services 137
Printer Software 139
License Agreement 139
3. RESTRICTIONS 140
Glossary 145
HEAD COLD 150
ZPL mode setting, 69 154
Zebra support, 3 154
Customer Order # 57516L-001 156

Comentarios a estos manuales

Sin comentarios

Zebra 170PAX4 Guía de usuario Pagina 40

Comentarios a estos manuales

Relacionado con productos y manuales para Impresoras De Etiquetas Zebra 170PAX4