Zebra S400 Guía de usuario Pagina 124
- Pagina / 146
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Troubleshooting
Printer Diagnostics
116
79695L-001 Rev. A ZM400/ZM600 User Guide 3/27/07
FEED Self Test
Different types of media may require different darkness settings. This section contains a
simple but effective method for determining the ideal darkness for printing bar codes that are
within specifications.
During the FEED self test, labels are printed at different darkness settings at two different print
speeds. The relative darkness and the print speed are printed on each label. The bar codes on
these labels may be ANSI-graded to check print quality.
The darkness value starts at three settings lower than the printer’s current darkness value
(relative darkness of –3) and increase until the darkness is three settings higher than the current
darkness value (relative darkness of +3).
Depending on the dot density of the printhead, seven labels are printed at each of the following
speeds:
• 203 dpi printers: 2 ips, 6 ips, and 10 ips
• 300 dpi printers: 2 ips, 6 ips, 8 ips
• 600 dpi printers: 2 ips, 4 ips
To perform a FEED self test, complete these steps:
1. Print a configuration label to show the printer’s current settings.
2. Turn off (O) the printer.
3. Press and hold FEED while turning on (I) the printer. Hold FEED until the first control
panel light turns off.
The printer prints a series of labels (Figure 20) at various speeds and at darkness settings
higher and lower than the darkness value shown on the configuration label.
Figure 20 • FEED Test Label
- ZM400/ZM600 1
- User Guide 1
- Declaration of Conformity 3
- Compliance Information 4
- Contents 5
- Who Should Use This Document 10
- Contacts 11
- Document Conventions 12
- FEED button 13
- CANCEL button 13
- About This Document 14
- Introduction 15
- External View 16
- Printer Media Compartment 17
- Control Panel 18
- Control Panel Buttons 19
- Control Panel Lights 20
- Printer Language Modes 21
- Printer Setup 23
- Before You Begin 24
- Handling the Printer 25
- Select a Site for the Printer 26
- Interface 27
- Standard or 27
- Optional on 27
- Characteristics 27
- I) may damage the 28
- O) position 31
- Power Cord Specifications 32
- Types of Media 33
- Ribbon Overview 35
- Ribbon Scratch Test 36
- Operations 37
- Media Paths 39
- Media Path 40
- Load Media 41
- Rear Feed 42
- Bottom Feed 42
- Roll Media (Continued) 43
- Fanfold Media (Continued) 43
- PAUSE to enable printing 44
- Close the printhead assembly 54
- Load Ribbon 55
- Ribbon Coated Outside 57
- (black ribbon spindle) 57
- Ribbon Coated Inside 57
- (gray ribbon spindle) 57
- Remove Used Ribbon 59
- Calibrate the Printer 60
- Adjust Printhead Pressure 61
- Inside Dial Outside Dial 62
- Configuration 63
- Setup Mode 64
- Exit Setup Mode 65
- Default Password Value 66
- Print a Configuration Label 67
- LIST NETWORK 68
- Control Panel Parameters 69
- Standard Printer Parameters 70
- To change the value shown: 71
- Parameter 71
- ZM400 ZM600 74
- Action/Explanation 75
- WARNING REPLACE 77
- To format a memory card: 80
- To initialize Flash memory: 81
- To print a sensor profile: 81
- LOAD BACKING prompt displays 82
- RELOAD ALL displays 82
- To skip these parameters: 90
- IDLE DISPLAY 92
- Replacing Printer Components 96
- Lubrication 96
- Clean the Exterior 97
- Routine Maintenance 100
- Cleaning Procedures 100
- Clean the Cutter Module 102
- I) the printer 103
- Troubleshooting 107
- Troubleshooting Checklists 108
- LCD Error Messages 109
- O) the printer 110
- HEAD COLD 111
- HEAD TOO HOT 111
- DEFRAGMENTING 112
- ERROR CONDITION 112
- CUTTER JAM 112
- OUT OF MEMORY 112
- (function) 112
- Print Quality Problems 113
- Note • A vertical drift of 115
- Calibration Problems 116
- Communications Problems 117
- Ribbon Problems 118
- LANGUAGE 119
- SAVE CHANGES in the 119
- Printer Diagnostics 121
- CANCEL Self Test 122
- PAUSE Self Test 123
- FEED Self Test 124
- Print Quality Description 126
- FEED and PAUSE Self Test 127
- Sensor Profile 129
- Specifications 131
- General Specifications 132
- Agency Approvals 133
- Printing Specifications 134
- Media Specifications 136
- Ribbon Specifications 137
- Printer Options 138
- Cutter Jam message, 104 140
- HEAD COLD message 140
- HEAD ELEMENT BAD message, 102 140
- HEAD TOO HOT message, 103 140
- INVALID HEAD message, 101 141
- OUT OF MEMORY message, 104 141
- PAPER OUT message, 102 142
- RIBBON IN message, 102 143
- RIBBON OUT message, 101 143
- THERMISTOR FAULT message 144
- © 2007 ZIH Corp 146
Relacionado con productos y manuales para Impresoras De Etiquetas Zebra S400
Impresoras De Etiquetas Zebra TTPM2 Especificaciones
(102 paginas)
(102 paginas)
Impresoras De Etiquetas Zebra A300 Guía de usuario
(38 paginas)
(38 paginas)
Impresoras De Etiquetas Zebra 105SL Especificaciones
(246 paginas)
(246 paginas)
Impresoras De Etiquetas Zebra A300 Guía de usuario
(36 paginas)
(36 paginas)
Impresoras De Etiquetas Zebra S400 Manual de usuario
(46 paginas)
(46 paginas)
Impresoras De Etiquetas Zebra S4M Especificaciones
(404 paginas)
(404 paginas)
Impresoras De Etiquetas Zebra Z6M Manual de usuario
(112 paginas)
(112 paginas)
Impresoras De Etiquetas Zebra ZT210 Manual de usuario
(168 paginas)
(168 paginas)
Impresoras De Etiquetas Zebra Z4Mplus Manual de usuario
(178 paginas)
(178 paginas)
Impresoras De Etiquetas Zebra QL+ Manual de usuario
(86 paginas)
(86 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.131 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales