Zebra Z4Mplus Manual de usuario descargar pdf (Pagina 41)

Printer Setup

Before You Begin

Z4Mplus and Z6Mplus User Guide 11

Non-Continuous Black Mark Labels

Non-continuous black mark labels have black marks printed on the back of the liner

indicating the start and end of each label (shown below).

Continuous Media

Continuous media (shown below) is one uninterrupted roll of material without gaps,

holes, notches, or black marks that allows the image to be printed anywhere on the

label.

Number Description

Black Mark

1 2 ... 36 37 38 39 40 41 42 43 44 45 46 ... 177 178

User Guide 1
Your Feedback Is Important 3
Feedback Form 4
Proprietary Statement 5
FCC Compliance Statement 6
Liability Disclaimer 6
Limitation of Liability 6
Copyrights 7
DECLARATION OF CONFORMITY 9
Warranty Information 11
Printer Products 12
Printhead Warranty Period 12
Supplies Products 13
Agreement 14
Table of Contents 21
Contents 25
Contacts 26
About this Document 27
Document Conventions 28
Related Documents 30
Introduction 31
Inspect the printer 32
Front Panel 33
Printer Side View 35
Printer Setup 37
Before You Begin 38
Types of Media 40
Continuous Media 41
Print Mode 42
Load Media and Ribbon 43
Load the Ribbon 44
Printhead Pressure Adjustment 46
Set Printhead Pressure 47
Rewind Media Alignment 48
Configuration Label 49
Basic Configuration 52
Basic Configuration Process 53
Position the Label Sensor 56
Transmissive Sensor 58
Communication 59
System Considerations 60
Cable Requirements 62
Printer Basics 63
Printer Overview 64
Front Panel Keys 66
Front Panel Lights 67
Load Roll Media 68
Cutter Mode 70
Peel-Off Mode 72
Liner Take-Up Mode 74
Liner Slide Tab 76
Liner Slide 76
Liner Removal 79
Rewind Mode 79
PAUSE to enable printing 80
Load Fanfold Media 82
Bottom Feed 83
Rear Feed 83
Remove the Ribbon 86
Leave the Setup Mode 90
Configuration 100
Selecting ZPL Mode 106
Label Positioning Parameters 108
SAVE SETTINGS 114
PRINTER READY 114
Routine Care and Adjustments 115
Cleaning Procedures 116
Clean the Exterior 117
Clean the Interior 117
Clean the Sensors 119
Clean the Rewind Option 120
Clean the Peel-Off Assembly 122
Clean the Cutter Module 123
Lubrication 124
Fuse Replacement 125
Troubleshooting 127
Error Conditions 128
Load Roll Media 129
page 15) 129
(page 64) and select 130
Warnings 131
Warning — CUTTER JAM 132
OUT OF MEMORY* 132
page 87 133
Wrinkled ribbon 134
Calibration 135
Communication Problems 136
Print Quality Problems 137
Printer Diagnostics 138
Cancel Self Test 139
Pause Self Test 140
Feed Self Test 141
Loading Factory Defaults 142
Specifications 143
General Specifications 144
Printing Specifications 145
Media Specifications 146
Ribbon Specifications 148
°, 90°, 180°, 270°) 150
Bar codes 151
AC Power Cord 152
DB-9 Connectors 153
Serial Data Communications 154
Cable Specifications 154
(Printer) 157
(Modem, etc.) 157
Connector 159
Parallel Data Port 161
Memory Cards 165
Extend Printhead Life 169
Challenge 170
Preventive Maintenance 171
Save-a-Printhead 172

Comentarios a estos manuales

Sin comentarios

Zebra Z4Mplus Manual de usuario Pagina 41

Comentarios a estos manuales

Relacionado con productos y manuales para Impresoras De Etiquetas Zebra Z4Mplus