Zebra Stripe Guía de usuario Pagina 149
- Pagina / 150
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
- User Guide 1
- Declaration of Conformity 3
- Compliance Information 4
- Contents 5
- Who Should Use This Document 10
- Contacts 11
- Bubbledot ICG font 12
- POWER ALERT 13
- CANCEL FEED 13
- About This Document 14
- Document Conventions 14
- Introduction 15
- External View 16
- FEED FEED 18
- Appearance 19
- Control Panel Lights 20
- Printer Media Compartment 21
- Printer Language Modes 22
- Printer Setup 23
- Before You Begin 24
- Handling the Printer 25
- Select a Site for the Printer 26
- Interface 27
- Standard or 27
- Optional on 27
- Characteristics 27
- I) may damage the 28
- O) position 30
- Power Cord Specifications 31
- Types of Media 32
- Ribbon Overview 34
- Adhesive Test 35
- Ribbon Scratch Test 35
- Operations 37
- Media Paths 38
- Start a Roll of Media 39
- Insert Media into the Printer 40
- Fanfold Media 41
- Load Media in Tear-Off Mode 42
- 4. Slide out the media guide 43
- Close the printhead assembly 44
- Load Media in Peel-Off Mode 45
- Slide out the media guide 46
- PAUSE to enable printing 49
- Load Media in Cutter Mode 50
- Load Ribbon 53
- Remove Used Ribbon 57
- Calibrate the Printer 58
- Adjust the Reflective Sensor 59
- Adjust Printhead Pressure 61
- If the media... Then 62
- Configuration 63
- Setup Mode 64
- If you wish to... Then 65
- PASSWORD and the number 0000 66
- Printing Configuration Labels 68
- SETTINGS 69
- NETWORK 70
- Select a Display Language 71
- DARKNESS 72
- TEAR OFF 73
- LABEL TOP 73
- X FORMS ADJUST 73
- LEFT POSITION 73
- Y FORMS ADJUST 73
- MEDIA TYPE 74
- SENSOR SELECT 74
- PRINT SPEED 75
- PRINT WIDTH 75
- KDU MODE 75
- COMPAT. MODE 75
- CONTROL CODES 76
- RESOLUTION 76
- Password Level 3 Parameters 77
- MODULE A 78
- MODULE B 78
- PARALLEL COMM 78
- PRINT PAGE 78
- PRINT FORMAT 78
- DATA BITS 79
- STATUS RESPONSE 79
- HOST HANDSHAKE 80
- CONTROL CHAR 80
- COMMAND CHAR 80
- DELIM. CHAR 81
- REPRINT MODE 81
- CHANGE RTC DATE 81
- Control Panel Parameters 82
- ZPL OVERRIDE 83
- SENSOR PROFILE 84
- Parameter Explanation 85
- To modify this parameter: 86
- Routine Maintenance 87
- Replacing Printer Components 88
- Lubrication 88
- Clean the Exterior 89
- Cleaning Procedures 90
- Clean the Peel Assembly 94
- Close the media door 96
- Clean the Cutter Module 97
- Troubleshooting Checklists 100
- RIBBON OUT 101
- O) the printer 102
- I) the printer 102
- HEAD COLD 103
- HEAD TOO HOT 103
- DEFRAGMENTING 104
- ERROR CONDITION 104
- CUTTER JAM 104
- HEAD ELE. BAD 104
- Memory Errors 105
- Print Quality Problems 106
- Troubleshooting 107
- Note • A vertical drift of 108
- Calibration Problems 109
- Communications Problems 110
- YES, the printer 111
- O) and then on (I) 112
- O) and then 112
- Printer Diagnostics 114
- CANCEL Self Test 115
- PAUSE Self Test 116
- FEED Self Test 117
- Print Quality Description 118
- FEED and PAUSE Self Test 120
- Sensor Profile 122
- Specifications 125
- General Specifications 126
- Agency Approvals 127
- Printing Specifications 128
- Media Specifications 129
- Ribbon Specifications 130
- ZPL II Commands 131
- Define Password 132
- End User License 133
- Agreement 133
- End User License Agreement 134
- Glossary 139
- Cutter Jam message, 104 144
- HEAD COLD message 145
- HEAD ELEMENT BAD message, 102 145
- HEAD TOO HOT message, 103 145
- RIBBON IN message, 102 146
- THERMISTOR FAULT message 147
Relacionado con productos y manuales para Impresoras De Etiquetas Zebra Stripe
(146 paginas)
(102 paginas)
(38 paginas)
(246 paginas)
(36 paginas)
(46 paginas)
(404 paginas)
(112 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.120 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales