Zebra Wireless Print Server Guía de usuario Pagina 106
- Pagina / 228
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
ZPL Commands for Wireless Operation
^WI
106
14143L-005 Rev. A Wireless User Guide 4/29/08
^WI
Change Wireless Network Settings
Description Use this command to change the wireless network settings. On Zebra
ZM400/ZM600™ and S4M™ printers running V53.15.xZ or later or on RZ400/RZ600™
printers running R53.16.x or later, Zebra recommends using ^ND on page 97 for these settings.
Format ^WIa,b,c,d,e,f,g,h,i
The following table identifies the parameters for this format.
Parameters Details
a = IP resolution Accepted Values:
A =All
B =BOOTP
C = DHCP and BOOTP
D = DHCP
G = Gleaning only (Not recommended when the
Wireless Print Server or Wireless Plus Print Server
is installed.)
R =RARP
P = Permanent
Default Value: A
b = IP address Accepted Values: Any properly formatted IP address in the
xxx.xxx.xxx.xxx format.
Default Value: 000.000.000.000
c = subnet mask Accepted Values: Any properly formatted subnet mask in the
xxx.xxx.xxx.xxx format.
Default Value: 000.000.000.000
d = default gateway Accepted Values: Any properly formatted gateway in the
xxx.xxx.xxx.xxx format.
Default Value: 000.000.000.000
e = WINS server address Accepted Values: Any properly formatted WINS server in the
xxx.xxx.xxx.xxx format.
Default Value: 000.000.000.000
f = connection timeout
checking
Accepted Values:
Y = yes
N = no
Default Value: Y
g = timeout value
Time, in seconds, before the connection times out.
Accepted Values: 0 through 9999
Default Value: 300
- ZebraNet 1
- Wireless User Guide 1
- Contents 3
- Section Description 10
- Contacts 11
- Document Conventions 12
- About This Document 13
- Introduction 15
- Hardware 16
- Firmware 16
- Access Point 19
- Technologies 20
- Systems 21
- Supported Security Types 22
- Security Type Supported? 23
- Wireless Plus Print Server 25
- = Active Print Server 25
- Wireless Print Server 25
- Configuration 29
- Any Other Wireless Printer 32
- 7. Click Next 33
- PSK Type to String 34
- PSK Name field 34
- Click OK 35
- To... Then 36
- Save Script to a file 37
- Wireless Radio Card 38
- 5. Turn on (I) the printer 39
- 6. Turn on (I) the printer 41
- Wireless Status 43
- Plus (+) for 105SL 44
- Status Indicator Meaning 44
- SIGNAL STRENGTH and 45
- SIGNAL QUALITY 45
- Network Configuration Label 46
- PAUSE/FEED 47
- Function 48
- WIRED PS CHECK? 48
- ^NP ZPL command 49
- PRIMARY NETWORK 50
- LOAD FROM EXT? 50
- ACTIVE PRINTSRVR 50
- IP PROTOCOL 50
- Parameter 51
- RESET NETWORK 52
- Parameter Explanation 53
- Wireless Status and Settings 55
- Troubleshooting 57
- Wireless Error Messages 58
- General Issues 58
- DEFAULT NET 59
- IP Issues 61
- WebView Web Pages 63
- IP ADDRESS 64
- Home Page 65
- View Printer Configuration 66
- 3. Click Submit Changes 67
- 4. Click on the statement 67
- Network Configuration Menu 69
- Print Listings on Label 69
- Media Setup Calibration 70
- ZPL Control Advanced Setup 71
- Network Configuration Screens 72
- SMTP TCP/IP 74
- X60.15.x and ZSPx 74
- Directory Listing 77
- Click Edit 79
- Button Function/Operation 80
- Alert Setup 81
- Printer Controls 84
- Button Function 85
- Print Server Settings 86
- Print Server: 88
- TCP/IP Configuration 88
- TCP/IP Logical Printing Ports 88
- Cancel Job 90
- View Configuration Sheet 91
- View Port Status Contact 91
- ZPL Commands 93
- Parameters Details 100
- Format ~WL 109
- Region Channel Mask 114
- Configure Wireless Securities 115
- Security Type 03: WEP 128-Bit 119
- Security Type 02: WEP 40-Bit 119
- Security Type 04: EAP-TLS 120
- Security Type 05: EAP-TTLS 120
- Security Type 06: EAP-FAST 120
- Security Type 07: PEAP 121
- Security Type 08: LEAP 121
- Security Type 09: WPA PSK 121
- Security Type 10: WPA EAP-TLS 122
- Security Type 13: WPA PEAP 123
- Security Type 14: WPA LEAP 123
- Security Type 15: Kerberos 123
- SGD Wireless Commands 125
- Overview 126
- Do commands: 127
- Command Structure 128
- Commands Details 129
- Security Type 2: WEP 40-Bit 194
- Security Type 3: WEP 128-Bit 195
- Security Type 4: EAP-TLS 195
- Security Type 5: EAP-TTLS 196
- Security Type 6: EAP-FAST 196
- Security Type 7: PEAP 197
- Security Type 8: LEAP 197
- Security Type 9: WPA PSK 197
- Glossary 217
- © 2008 ZIH Corp 228
Relacionado con productos y manuales para Los servidores de impresión Zebra Wireless Print Server
Los servidores de impresión Zebra II Especificaciones
(262 paginas)
(262 paginas)
Los servidores de impresión Zebra 10/100 Guía de usuario
(132 paginas)
(132 paginas)
Los servidores de impresión Zebra II Especificaciones
(412 paginas)
(412 paginas)
Los servidores de impresión Zebra 10/100 Guía de usuario
(162 paginas)
(162 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.024 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales