Zebra S4M Manual de usuario Pagina 120
- Pagina / 132
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Proprietary Statement
114
13290L-001 Rev. A S4M User Guide 10/21/05
• Consult the dealer or an experienced radio/TV technician for help.
The user is cautioned that any changes or modifications not expressly approved by Zebra
Technologies could void the user’s authority to operate the equipment. To ensure compliance,
this printer must be used with Shielded Communication Cables.
Canadian DOC Compliance Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Liability Disclaimer
Zebra Technologies takes steps to ensure that its published Engineering specifications and
manuals are correct; however, errors do occur. Zebra Technologies reserves the right to correct
any such errors and disclaims liability resulting therefrom.
Limitation of Liability
In no event shall Zebra Technologies or anyone else involved in the creation, production, or
delivery of the accompanying product (including hardware and software) be liable for any
damages whatsoever (including, without limitation, consequential damages including loss of
business profits, business interruption, or loss of business information) arising out of the use
of, the results of use of, or inability to use such product, even if Zebra Technologies has been
advised of the possibility of such damages. Some jurisdictions do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion may
not apply to you.
- User Guide 1
- Contents 3
- Who Should Use This Document 8
- Contacts 9
- Document Conventions 10
- FEED button 11
- CANCEL button 11
- About This Document 12
- Introduction 13
- External View 14
- Control Panel 15
- FEED FEED 16
- Appearance 17
- Control Panel Lights 18
- Printer Media Compartment 19
- Printer Language Modes 20
- Printer Setup 21
- Before You Begin 22
- Inspect the Printer 23
- Report Shipping Damage 23
- Store the Printer 23
- Shipping 23
- Select a Site for the Printer 24
- Power Cord Specifications 26
- Connector Locations 27
- Types of Connections 28
- Operations 29
- 16.4 ft (5 m) maximum 30
- Types of Media 31
- Outside Inside 33
- Adhesive Test 34
- Ribbon Scratch Test 34
- Labels Tag Stock 36
- Roll Media 37
- Fanfold Media 38
- Load Media in Tear-Off Mode 39
- 4. Slide out the media guide 40
- Close the printhead assembly 41
- Load Media in Peel-Off Mode 42
- Slide out the media guide 43
- Tear-off/peel-off bar 45
- Peel assembly 45
- Peeling starts automatically 46
- Load Ribbon 47
- Caution • 50
- 1). At the same 51
- Calibrate the Printer 52
- Position the Media Sensors 53
- Left Dial Right Dial 55
- If the media... Then 56
- Configuration 57
- ENTER button 58
- MENU or any arrow button 59
- Password 60
- Printing Configuration Labels 62
- SETTINGS 63
- LIST NETWORK 64
- Select a Display Language 65
- Parameter Explanation 66
- To modify this parameter: 66
- TEAR OFF 67
- LABEL TOP 67
- X FORMS ADJUST 67
- Y FORMS ADJUST 67
- Media Type Sensor Used 68
- PRINT SPEED 69
- PRINT WIDTH 69
- COMPAT. MODE 69
- Control Panel LCD Display 70
- To print labels: 71
- PRINT PAGE 72
- PRINT FORMAT 72
- DATA BITS 72
- COMMAND CHAR 74
- DELIM. CHAR 74
- CONTROL CHAR 74
- CHANGE RTC DATE 75
- CHANGE RTC TIME 75
- 1. Press ENTER 76
- 1. Press ENTER to select YES 76
- ZPL OVERRIDE 77
- EPL OVERRIDE 77
- SENSOR PROFILE 77
- ZebraNet 80
- Routine Maintenance 83
- Lubrication 84
- Cleaning Procedures 84
- Clean the Peel-Off Assembly 88
- Troubleshooting Checklists 92
- LCD Error Messages 93
- HEAD COLD 94
- HEAD ELE. BAD 94
- Memory Errors 95
- Print Quality Problems 96
- Calibration Problems 99
- Communications Problems 100
- O) and then 101
- Troubleshooting 102
- O) and then On (l) 103
- CANCEL Self Test 104
- PAUSE Self Test 105
- FEED Self Test 106
- Printer Diagnostics 107
- Print Quality Description 108
- O) and then back 109
- Specifications 111
- General Specifications 112
- Agency Approvals 113
- Printing Specifications 114
- Media Specifications 115
- Ribbon Specifications 116
- ZPL II Commands 117
- Parameters Details 118
- Proprietary Statement 119
- Liability Disclaimer 120
- Limitation of Liability 120
- Glossary 121
- HEAD COLD message, 88 126
- HEAD TOO HOT message, 87 126
- RIBBON IN message, 87 128
- Part Number: 13290L-001 132
- © 2005 ZIH Corp 132
Relacionado con productos y manuales para No Zebra S4M
No Zebra MIX05120 Manual de usuario
(2 paginas)
(2 paginas)
No Zebra GK888t Manual de usuario
(20 paginas)
(20 paginas)
No Zebra GK420d Manual de usuario
(20 paginas)
(20 paginas)
No Zebra P100i Manual de usuario
(76 paginas)
(76 paginas)
No Zebra RW 220 Manual de usuario
(16 paginas)
(16 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales