Zebra S4M Manual de usuario descargar pdf (Pagina 89)

Routine Maintenance

Cleaning Procedures

10/21/05 S4M User Guide 13290L-001 Rev. A

6. Use the swab to remove excess adhesive from the tear-off/peel-off bar. Allow the solvent

to evaporate.

7. Close the printhead assembly and the media door.

The printer is ready to operate.

Important • Apply minimum force when cleaning the tear-off/peel-off bar. Excessive

force can cause the tear-off/peel-off bar to bend, which could have a negative effect on

peel performance.

1 2 ... 84 85 86 87 88 89 90 91 92 93 94 ... 131 132

User Guide 1
Contents 3
Who Should Use This Document 8
Contacts 9
Document Conventions 10
FEED button 11
CANCEL button 11
About This Document 12
Introduction 13
External View 14
Control Panel 15
FEED FEED 16
Appearance 17
Control Panel Lights 18
Printer Media Compartment 19
Printer Language Modes 20
Printer Setup 21
Before You Begin 22
Inspect the Printer 23
Report Shipping Damage 23
Store the Printer 23
Shipping 23
Select a Site for the Printer 24
Power Cord Specifications 26
Connector Locations 27
Types of Connections 28
Operations 29
16.4 ft (5 m) maximum 30
Types of Media 31
Outside Inside 33
Adhesive Test 34
Ribbon Scratch Test 34
Labels Tag Stock 36
Roll Media 37
Fanfold Media 38
Load Media in Tear-Off Mode 39
4. Slide out the media guide 40
Close the printhead assembly 41
Load Media in Peel-Off Mode 42
Slide out the media guide 43
Tear-off/peel-off bar 45
Peel assembly 45
Peeling starts automatically 46
Load Ribbon 47
Caution • 50
1). At the same 51
Calibrate the Printer 52
Position the Media Sensors 53
Left Dial Right Dial 55
If the media... Then 56
Configuration 57
ENTER button 58
MENU or any arrow button 59
Password 60
Printing Configuration Labels 62
SETTINGS 63
LIST NETWORK 64
Select a Display Language 65
Parameter Explanation 66
To modify this parameter: 66
TEAR OFF 67
LABEL TOP 67
X FORMS ADJUST 67
Y FORMS ADJUST 67
Media Type Sensor Used 68
PRINT SPEED 69
PRINT WIDTH 69
COMPAT. MODE 69
Control Panel LCD Display 70
To print labels: 71
PRINT PAGE 72
PRINT FORMAT 72
DATA BITS 72
COMMAND CHAR 74
DELIM. CHAR 74
CONTROL CHAR 74
CHANGE RTC DATE 75
CHANGE RTC TIME 75
1. Press ENTER 76
1. Press ENTER to select YES 76
ZPL OVERRIDE 77
EPL OVERRIDE 77
SENSOR PROFILE 77
ZebraNet 80
Routine Maintenance 83
Lubrication 84
Cleaning Procedures 84
Clean the Peel-Off Assembly 88
Troubleshooting Checklists 92
LCD Error Messages 93
HEAD COLD 94
HEAD ELE. BAD 94
Memory Errors 95
Print Quality Problems 96
Calibration Problems 99
Communications Problems 100
O) and then 101
Troubleshooting 102
O) and then On (l) 103
CANCEL Self Test 104
PAUSE Self Test 105
FEED Self Test 106
Printer Diagnostics 107
Print Quality Description 108
O) and then back 109
Specifications 111
General Specifications 112
Agency Approvals 113
Printing Specifications 114
Media Specifications 115
Ribbon Specifications 116
ZPL II Commands 117
Parameters Details 118
Proprietary Statement 119
Liability Disclaimer 120
Limitation of Liability 120
Glossary 121
HEAD COLD message, 88 126
HEAD TOO HOT message, 87 126
RIBBON IN message, 87 128
Part Number: 13290L-001 132

Comentarios a estos manuales

Sin comentarios

Zebra S4M Manual de usuario Pagina 89

Comentarios a estos manuales

Relacionado con productos y manuales para No Zebra S4M