Zebra 96XiIII Plus Guía de usuario descargar pdf (Pagina 130)

Print Modes and Options

Print Modes

130

13383L-004 Rev. A XiIIIPlus/R110Xi/R170Xi User Guide 9/6/07

2. Pull out the spindle hook.

3. Slide the media liner off of the spindle and discard.

Rewind Peel

Rewind

Peel

1 2 ... 125 126 127 128 129 130 131 132 133 134 135 ... 229 230

User Guide 1
Declaration of Conformity 3
Compliance Information 4
Contents 10
About This Document 11
Section Description 12
Contacts 13
Document Conventions 14
SETUP/EXIT button 15
CALIBRATE button 15
Introduction 17
External View 18
Printer Components 19
Control Panel 20
Control Panel LCD 21
Control Panel Buttons 21
Appearance 22
Printer Setup 25
Before You Begin 26
Temperature Relative Humidity 27
Select a Site for the Printer 28
Interface 29
Standard or 29
Optional on 29
Characteristics 29
) may damage the 30
O) position 33
Power Cord Specifications 34
Types of Media 35
Ribbon Overview 37
If the ribbon... Then 38
Operations 39
Prepare the Media for Loading 40
Fanfold Media 41
If… Then… 42
Load Media in Tear-Off Mode 44
Load Ribbon 49
Calibrate the Printer 56
SENSOR PROFILE 57
MEDIA AND RIBBON 57
CALIBRATE 57
Adjust Media Sensors 58
Lower Media Sensor 60
Toggle Position Adjustment 61
Printhead Pressure Adjustment 62
Configuration 65
Exit Setup Mode 67
Default Password Value 68
LIST SETUP 69
LIST NETWORK 70
Control Panel Parameters 71
Standard Printer Parameters 72
Action/Explanation 73
TEAR OFF +000 73
- + 73
PRINT MODE 73
-TEAR-OFF + 73
To change the value shown: 74
Parameter 74
PRINT WIDTH 75
- 104 0/8 MM + 75
MAXIMUM LENGTH 76
39.0IN 988MM 76
To reset the media counter: 78
To reset the ribbon counter: 78
To format a memory card: 82
To initialize Flash memory: 83
PRINT 84
ZPL MODE 90
- ZPL II + 90
MEDIA POWER UP 90
- CALIBRATION+ 90
LEFT POSITION 92
- ±0000 + 92
HEAD TEST COUNT 93
- 0000 + 93
HEAD RESISTOR 94
- 0500 OHMS + 94
VERIFIER PORT 94
APPLICATOR PORT 95
- OFF + 95
START PRINT SIG 95
- PULSE MODE + 95
To skip these parameters: 96
IDLE DISPLAY 98
RTC TIME 98
- 14:55 + 98
- ENGLISH + 98
Printer Options 100
SETUP/EXIT 101
Load Media in Peel-Off Mode 102
1) counter-clockwise 103
RIBBON OUT error 104
1), under the 105
Print Modes 106
Print Modes and Options 106
Load Media in Cutter Mode 109
Install the Rewind Plate 128
If... Then 129
Pull out the spindle hook 130
Routine Maintenance 131
Replacing Printer Components 132
Lubrication 132
Clean the Exterior 133
CLEAN HEAD NOW 134
Clean the Sensors 137
Lower media sensor 139
Clean the Snap Plate 140
Clean the Cutter 142
Replace the Fuse 143
Troubleshooting 145
Troubleshooting Checklists 146
LCD Error Messages 147
O) the printer 148
I) the printer 148
HEAD COLD 149
HEAD TOO HOT 149
DEFRAGMENTING 150
ERROR CONDITION 150
CUTTER JAM 150
OUT OF MEMORY 150
(function) 150
Print Quality Problems 151
Note • A vertical drift of 153
Calibration Problems 155
NONE. See 156
Ribbon Problems 157
RFID TAG 158
MEDIA POWER UP and 159
O) and then back on (I) too 160
LANGUAGE 161
SAVE CHANGES in the 161
CANCEL self tests 163
CANCEL Self Test 164
PAUSE Self Test 165
FEED Self Test 166
Printer Diagnostics 167
Print Quality Description 168
FEED and PAUSE Self Test 170
RIBBON (2). If 172
MEDIA (3) for the media 172
Data Ports 173
Description 174
Serial Data Port 176
RS-232 Interface Connections 178
Modem Connection 179
USB 2.0 Port 180
Applicator Signals 181
Replace 183
PC Cards 189
PCMCIA PC Cards 190
PAUSE light flashes 191
PAUSE light flashes only 191
Specifications 193
Features 194
Bar Codes 195
Agency Approvals 196
General Specifications 198
Print Specifications by Model 200
Ribbon Specifications 203
170XiIIIPlus and 220XiIIIPlus 204
Media Specifications 205
End User License 211
Agreement 211
End User License Agreement 212
Glossary 217
Numerics 221
Cutter Jam message, 150 222
HEAD COLD message 223
HEAD ELEMENT BAD message, 148 223
HEAD TOO HOT message, 149 223
PAPER OUT message, 148 224
OUT OF MEMORY message, 150 224
RIBBON IN message, 148 226
RIBBON OUT message, 147 226
THERMISTOR FAULT message 227
XML-enabled printing, 100 228
ZPL mode setting, 90 228

Comentarios a estos manuales

Sin comentarios

Zebra 96XiIII Plus Guía de usuario Pagina 130

Comentarios a estos manuales

Relacionado con productos y manuales para Impresoras De Etiquetas Zebra 96XiIII Plus