Zebra 105SL Plus Guía de usuario Pagina 44
- Pagina / 180
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Printer Setup and Operation
Connect the Printer to a Power Source
44
P1056468-002 7/3/13
3. Turn on (I) the printer.
The printer boots up and performs a self-test.
Power Cord Specifications
Depending on how your printer was ordered, a power cord may or may not be included. If one
is not included or if the one included is not suitable for your requirements, see Figure 5 and
refer to the following guidelines:
• The overall cord length must be less than 9.8 ft. (3 m).
• The cord must be rated for a minimum of 10 A, 250 V.
• The chassis ground (earth) must be connected to ensure safety and reduce electromagnetic
interference.
Caution • For personnel and equipment safety, always use an approved three-conductor
power cord specific to the region or country intended for installation. This cord must use an
IEC 320 female connector and the appropriate region-specific, three-conductor grounded
plug configuration.
- 105SLPlus™ 1
- User Guide 1
- Part Number: P1056468-002 2
- Declaration of Conformity 3
- Compliance Information 4
- Contents 5
- Who Should Use This Document 10
- Document Conventions 11
- About This Document 12
- Introduction 13
- Printer Components 14
- Control Panel 15
- Control Panel Display 17
- Perform an action 18
- Change Parameter Values 18
- Default Password Value 20
- WARNING CLEAN PRINTHEAD 23
- YES to reset 23
- WARNING REPLACE HEAD 24
- 3. Do you want to continue? 26
- PERMANENT 33
- Printer Setup and 37
- Operation 37
- Handling the Printer 38
- Printer Setup and Operation 39
- I) may damage the 40
- Data Cables 42
- 115 V AC 43
- 230 V AC 43
- Power Cord Specifications 44
- Printer Setup 46
- Types of Media 47
- Ribbon Overview 49
- Adhesive Test 50
- Ribbon Scratch Test 50
- Select a Print Mode 51
- Load the Ribbon 54
- If… Then… 55
- 2) until it locks into place 58
- Load the Media 59
- 1) all the way out 60
- Bottom Feed 61
- Rear Feed 61
- RIBBON OUT error 62
- 1), under the 63
- Rewind Mode on page 72 64
- Mode on page 77 64
- 11. Close the media door 66
- Printer Configuration 81
- Print Settings 83
- ~JS when received 87
- • the non-resettable counter 90
- Important • 94
- Directory Listing 95
- Network Settings 96
- Print Server Settings > 99
- Factory Print Server Settings 99
- Language Settings 100
- • ZPL II 101
- Sensor Settings 102
- Port Settings 103
- Changing Printer Settings 104
- DSR/DTR for host handshake 105
- ZEBRA response messages are 105
- LOAD BACKING 106
- Raise the media door 107
- If you are using… Then… 108
- REMOVE RIBBON 109
- CALIBRATING 110
- PLEASE WAIT 110
- RELOAD ALL 110
- Close the media door 111
- Remove Used Ribbon 112
- If... Then 113
- Pull out the spindle hook 114
- Upper Media Sensor 115
- Routine Maintenance 116
- Lower Media Sensor 118
- Toggle Position Adjustment 119
- I) the printer.) 120
- Printhead Pressure Adjustment 121
- Replacing Printer Components 124
- Lubrication 124
- CLEAN HEAD NOW appears 125
- Clean the Sensors 128
- Transmissive Media Sensor 129
- Clean the Snap Plate 130
- Clean the Cutter 134
- Troubleshooting 135
- Printing Issues 136
- Error Messages 139
- 1) is likely 140
- O) the printer 141
- I) the printer 141
- Display/ 143
- Printer Condition 143
- Calibration Problems 144
- Communications Problems 145
- Ribbon Problems 146
- Miscellaneous Issues 147
- Printer Diagnostics 148
- CANCEL Self Test 149
- PAUSE Self Test 150
- FEED Self Test 151
- Print Quality Description 152
- FEED + PAUSE Self Test 154
- CANCEL + PAUSE Self Test 154
- FE indicates a framing error 155
- PE indicates a parity error 155
- NE indicates noise 155
- Sensor Profile 156
- MEDIA (3) for the media 157
- Specifications 159
- Features 160
- Bar Codes 161
- General Specifications 162
- Print Specifications 163
- Media Specifications 164
- Ribbon Specifications 165
- Glossary 167
- 7/3/13 P1056468-002 171
- P1056468-002 7/3/13 172
- 7/3/13 P1056468-002 173
Relacionado con productos y manuales para Impresión y escaneo Zebra 105SL Plus
Impresión y escaneo Zebra EM 220 Especificaciones
(67 paginas)
(67 paginas)
Impresión y escaneo Zebra EM 220 Manual de usuario
(30 paginas)
(30 paginas)
Impresión y escaneo Zebra S-500 Guía de usuario
(80 paginas)
(80 paginas)
Impresión y escaneo Zebra 105Se Especificaciones
(110 paginas)
(110 paginas)
Impresión y escaneo Zebra G-SERIES Guía de usuario
(58 paginas)
(58 paginas)
Impresión y escaneo Zebra RZ Series Guía de usuario
(154 paginas)
(154 paginas)
Impresión y escaneo Zebra CPCL Especificaciones
(70 paginas)
(70 paginas)
Impresión y escaneo Zebra TTPM2 Especificaciones
(140 paginas)
(140 paginas)
Impresión y escaneo Zebra R2844-Z Manual de usuario
(86 paginas)
(86 paginas)
Impresión y escaneo Zebra CPCL Especificaciones
(497 paginas)
(497 paginas)
Impresión y escaneo Zebra GK420t Guía de usuario
(22 paginas)
(22 paginas)
Impresión y escaneo Zebra 2746e Manual de usuario
(66 paginas)
(66 paginas)
Impresión y escaneo Zebra MZ series Especificaciones
(53 paginas)
(53 paginas)
Impresión y escaneo Zebra 110Xi4 Manual de usuario
(22 paginas)
(22 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales