Zebra 105SL Plus Guía de usuario descargar pdf (Pagina 77)

Printer Setup and Operation

Load the Media

7/3/13 P1056468-002

Final Steps for Cutter Mode 7.

Align the media with the inner media guide (1). Slide in the outer media guide (2) until it

just touches the edge of the media.

Caution • The cutter blade is sharp. Do not touch or rub the blade with your fingers.

Thread the media forward until it passes under the printhead assembly (1), under the

snap plate (

2), and through the cutter assembly (3).

1 2 ... 72 73 74 75 76 77 78 79 80 81 82 ... 179 180

105SLPlus™ 1
User Guide 1
Part Number: P1056468-002 2
Declaration of Conformity 3
Compliance Information 4
Contents 5
Who Should Use This Document 10
Document Conventions 11
About This Document 12
Introduction 13
Printer Components 14
Control Panel 15
Control Panel Display 17
Perform an action 18
Change Parameter Values 18
Default Password Value 20
WARNING CLEAN PRINTHEAD 23
YES to reset 23
WARNING REPLACE HEAD 24
3. Do you want to continue? 26
PERMANENT 33
Printer Setup and 37
Operation 37
Handling the Printer 38
Printer Setup and Operation 39
I) may damage the 40
Data Cables 42
115 V AC 43
230 V AC 43
Power Cord Specifications 44
Printer Setup 46
Types of Media 47
Ribbon Overview 49
Adhesive Test 50
Ribbon Scratch Test 50
Select a Print Mode 51
Load the Ribbon 54
If… Then… 55
2) until it locks into place 58
Load the Media 59
1) all the way out 60
Bottom Feed 61
Rear Feed 61
RIBBON OUT error 62
1), under the 63
Rewind Mode on page 72 64
Mode on page 77 64
11. Close the media door 66
Printer Configuration 81
Print Settings 83
~JS when received 87
• the non-resettable counter 90
Important • 94
Directory Listing 95
Network Settings 96
Print Server Settings > 99
Factory Print Server Settings 99
Language Settings 100
• ZPL II 101
Sensor Settings 102
Port Settings 103
Changing Printer Settings 104
DSR/DTR for host handshake 105
ZEBRA response messages are 105
LOAD BACKING 106
Raise the media door 107
If you are using… Then… 108
REMOVE RIBBON 109
CALIBRATING 110
PLEASE WAIT 110
RELOAD ALL 110
Close the media door 111
Remove Used Ribbon 112
If... Then 113
Pull out the spindle hook 114
Upper Media Sensor 115
Routine Maintenance 116
Lower Media Sensor 118
Toggle Position Adjustment 119
I) the printer.) 120
Printhead Pressure Adjustment 121
Replacing Printer Components 124
Lubrication 124
CLEAN HEAD NOW appears 125
Clean the Sensors 128
Transmissive Media Sensor 129
Clean the Snap Plate 130
Clean the Cutter 134
Troubleshooting 135
Printing Issues 136
Error Messages 139
1) is likely 140
O) the printer 141
I) the printer 141
Display/ 143
Printer Condition 143
Calibration Problems 144
Communications Problems 145
Ribbon Problems 146
Miscellaneous Issues 147
Printer Diagnostics 148
CANCEL Self Test 149
PAUSE Self Test 150
FEED Self Test 151
Print Quality Description 152
FEED + PAUSE Self Test 154
CANCEL + PAUSE Self Test 154
FE indicates a framing error 155
PE indicates a parity error 155
NE indicates noise 155
Sensor Profile 156
MEDIA (3) for the media 157
Specifications 159
Features 160
Bar Codes 161
General Specifications 162
Print Specifications 163
Media Specifications 164
Ribbon Specifications 165
Glossary 167
7/3/13 P1056468-002 171
P1056468-002 7/3/13 172
7/3/13 P1056468-002 173

Comentarios a estos manuales

Sin comentarios

Zebra 105SL Plus Guía de usuario Pagina 77

Comentarios a estos manuales

Relacionado con productos y manuales para Impresión y escaneo Zebra 105SL Plus