Zebra 110PAX4 Guía de usuario descargar pdf (Pagina 42)

Operations

Load Media

57512L-004 Rev. A 110PAX4/R110PAX4 User Guide 6/29/11

4. Slide the outer media guide (1) all the way out.

Caution • The printhead may be hot and could cause severe burns. Allow the

printhead to cool.

Open the printhead assembly by unlatching the printhead latch (1) from the

locking pin (

2).

1 2 ... 37 38 39 40 41 42 43 44 45 46 47 ... 163 164

110PAX4™/R110PAX4™ 1
User Guide 1
Part Number: 57512L-004 2
DECLARATION OF INCORPORATION 3
Compliance Information 4
Contents 5
Who Should Use This Document 10
T: Telephone 11
F: Facsimile 11
E: E-mail 11
Bubbledot ICG font 12
Liquid Crystal Display (LCD) 13
Lights/LEDs 13
About This Document 14
Document Conventions 14
Introduction 15
Print Engine Exterior View 16
Control Panel 17
CANCEL is ignored 18
CANCEL until 18
Power On/Off Switch 20
Print Engine Setup 21
Before You Begin 22
Handling the Print Engine 23
Recycle the Print Engine 24
Print Engine Installation 25
5 mounting screws 26
- 0.218 in. (5.5 mm) through 26
Power Cord Specifications 34
Types of Media 35
Ribbon Overview 37
Adhesive Test 38
Ribbon Scratch Test 38
Operations 39
Load Media 40
Left-Hand Right-Hand 41
16. Close the media door 45
Load Ribbon 46
Figure 16 • Loaded Ribbon 47
1) until it latches onto the 51
Remove Used Ribbon 52
Calibrate the Print Engine 53
Transmissive Media Sensor 55
Ribbon Sensor 55
Reflective Media Sensor 55
If the media... Then 56
Configuration 57
Setup Mode 58
Exit Setup Mode 59
Default Password Value 60
LIST SETUP 61
LIST NETWORK 62
Control Panel Parameters 63
Parameter Action/Explanation 64
To change the value shown: 64
BACKFEED SPEED 65
2 IPS + 65
TEAR OFF +000 65
- + 65
Parameter 66
PRINT WIDTH 67
- 168 0/8 MM + 67
MAXIMUM LENGTH 68
39.0IN 988MM 68
To reset the media counter: 70
To reset the ribbon counter: 70
Action/Explanation 73
To format a memory card: 74
To initialize Flash memory: 75
SENSOR PROFILE 76
PRINT 76
LEFT POSITION 83
- ±0000 + 83
HEAD RESISTOR 83
- 0500 OHMS + 83
APPLICATOR PORT 84
- OFF + 84
ERROR ON PAUSE 84
- ENABLED + 84
^SP command 86
To skip these parameters: 87
CLEAN HEAD NOW appears 90
Clean the Media Compartment 91
Clean the Sensors 91
Door-open sensor 92
Ribbon sensor reflector 92
Ribbon sensor 92
Toggle Positioning 95
I) the printer.) 96
7/16 inch 97
Printhead Pressure Adjustment 98
Routine Maintenance 100
Power Fuse Replacement 100
Troubleshooting 101
Troubleshooting Checklists 102
ERROR CONDITION 103
RIBBON OUT 103
O) the print engine 104
I) the print engine 104
HEAD COLD 105
HEAD TOO HOT 105
DEFRAGMENTING 106
OUT OF MEMORY 106
(function) 106
Memory Errors 107
Print Quality Problems 108
Note • A vertical drift of 110
NONE. See 112
Ribbon Problems 113
RFID Problems 114
LANGUAGE 117
SAVE CHANGES in the 117
Print Engine Diagnostics 119
CANCEL Self Test 120
PAUSE Self Test 121
FEED Self Test 122
Print Quality Description 124
FEED and PAUSE Self Test 126
Parameter Controlled By 127
J8 Interface Fixed 128
J7 Interface Fixed 128
Twinax/Coax ID ZPL 128
Sensor Profile 130
Data Ports 131
Parallel Data Port 132
36-Pin Connectors 133
Serial Data Port 134
Pin Configuration 135
RS-232 Interface Connections 136
Modem Connection 137
Applicator Signals 138
Caution • Replace 140
Isolated (External Power) 144
Non-Isolated (Internal Print 144
Engine Power) 144
Fuse and Jumper Locations 145
Specifications 147
General Specifications 148
Communications Specifications 149
Other Standard Features 150
Additional Options 150
Agency Approvals 151
Media Specifications 153
Ribbon Specifications 154
Printing Specifications 155
Bar Codes 156

Comentarios a estos manuales

Sin comentarios

Zebra 110PAX4 Guía de usuario Pagina 42

Comentarios a estos manuales

Relacionado con productos y manuales para Impresión y escaneo Zebra 110PAX4