Zebra 110PAX4 Guía de usuario Pagina 77
- Pagina / 164
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
77
Configuration
Control Panel Parameters
6/29/11 110PAX4/R110PAX4 User Guide 57512L-004 Rev. A
Calibrate Media and Ribbon Sensor Sensitivity
Use this procedure to adjust sensitivity of media and ribbon sensors.
Important • Follow this procedure exactly as presented. All of the
steps must be performed even if only one of the sensors requires
adjustment. You may press the left oval at any step in this procedure
to cancel the process.
To perform a media and ribbon sensor calibration:
1. Press the right oval to start the calibration procedure.
The
LOAD BACKING prompt displays.
2. Open the printhead.
3. Remove approximately 8 in. (203 mm) of labels from the backing, and
pull the media into the print engine so that only the backing is between
the media sensors.
4. Leave the printhead open.
5. Press the right oval
PLUS (+) to continue.
The
REMOVE RIBBON prompt displays.
6. Remove the ribbon (if used).
7. Close the printhead.
8. Press the right oval to continue.
The message
CALIBRATING PLEASE WAIT displays.
The print engine adjusts the scale (gain) of the signals that it receives
from the media and ribbon sensors based on the specific media and
ribbon combination being used. On the sensor profile, this essentially
corresponds to moving the peak of the graph up or down to optimize
the readings for your application.
When calibration is complete,
RELOAD ALL displays.
9. Open the printhead and pull the media forward until a label is
positioned under the media sensor.
10. Reload the ribbon (if used).
11. Close the printhead.
12. Press the right oval to continue.
The print engine performs an auto-calibration. During this process, the
print engine checks the readings for the media and ribbon based on the
new scale established, determines the label length, and determines the
print mode. To see the new readings on the new scale, print a sensor
profile.
Table 7 • Print Engine Parameters (Page 14 of 25)
Parameter
Action/Explanation
MEDIA AND RIBBON
CALIBRATE
- 110PAX4™/R110PAX4™ 1
- User Guide 1
- Part Number: 57512L-004 2
- DECLARATION OF INCORPORATION 3
- Compliance Information 4
- Contents 5
- Who Should Use This Document 10
- T: Telephone 11
- F: Facsimile 11
- E: E-mail 11
- Bubbledot ICG font 12
- Liquid Crystal Display (LCD) 13
- Lights/LEDs 13
- About This Document 14
- Document Conventions 14
- Introduction 15
- Print Engine Exterior View 16
- Control Panel 17
- CANCEL is ignored 18
- CANCEL until 18
- Power On/Off Switch 20
- Print Engine Setup 21
- Before You Begin 22
- Handling the Print Engine 23
- Recycle the Print Engine 24
- Print Engine Installation 25
- 5 mounting screws 26
- - 0.218 in. (5.5 mm) through 26
- Power Cord Specifications 34
- Types of Media 35
- Ribbon Overview 37
- Adhesive Test 38
- Ribbon Scratch Test 38
- Operations 39
- Load Media 40
- Left-Hand Right-Hand 41
- 16. Close the media door 45
- Load Ribbon 46
- Figure 16 • Loaded Ribbon 47
- 1) until it latches onto the 51
- Remove Used Ribbon 52
- Calibrate the Print Engine 53
- Transmissive Media Sensor 55
- Ribbon Sensor 55
- Reflective Media Sensor 55
- If the media... Then 56
- Configuration 57
- Setup Mode 58
- Exit Setup Mode 59
- Default Password Value 60
- LIST SETUP 61
- LIST NETWORK 62
- Control Panel Parameters 63
- Parameter Action/Explanation 64
- To change the value shown: 64
- BACKFEED SPEED 65
- 2 IPS + 65
- TEAR OFF +000 65
- - + 65
- Parameter 66
- PRINT WIDTH 67
- - 168 0/8 MM + 67
- MAXIMUM LENGTH 68
- 39.0IN 988MM 68
- To reset the media counter: 70
- To reset the ribbon counter: 70
- Action/Explanation 73
- To format a memory card: 74
- To initialize Flash memory: 75
- SENSOR PROFILE 76
- PRINT 76
- LEFT POSITION 83
- - ±0000 + 83
- HEAD RESISTOR 83
- - 0500 OHMS + 83
- APPLICATOR PORT 84
- - OFF + 84
- ERROR ON PAUSE 84
- - ENABLED + 84
- ^SP command 86
- To skip these parameters: 87
- CLEAN HEAD NOW appears 90
- Clean the Media Compartment 91
- Clean the Sensors 91
- Door-open sensor 92
- Ribbon sensor reflector 92
- Ribbon sensor 92
- Toggle Positioning 95
- I) the printer.) 96
- 7/16 inch 97
- Printhead Pressure Adjustment 98
- Routine Maintenance 100
- Power Fuse Replacement 100
- Troubleshooting 101
- Troubleshooting Checklists 102
- ERROR CONDITION 103
- RIBBON OUT 103
- O) the print engine 104
- I) the print engine 104
- HEAD COLD 105
- HEAD TOO HOT 105
- DEFRAGMENTING 106
- OUT OF MEMORY 106
- (function) 106
- Memory Errors 107
- Print Quality Problems 108
- Note • A vertical drift of 110
- NONE. See 112
- Ribbon Problems 113
- RFID Problems 114
- LANGUAGE 117
- SAVE CHANGES in the 117
- Print Engine Diagnostics 119
- CANCEL Self Test 120
- PAUSE Self Test 121
- FEED Self Test 122
- Print Quality Description 124
- FEED and PAUSE Self Test 126
- Parameter Controlled By 127
- J8 Interface Fixed 128
- J7 Interface Fixed 128
- Twinax/Coax ID ZPL 128
- Sensor Profile 130
- Data Ports 131
- Parallel Data Port 132
- 36-Pin Connectors 133
- Serial Data Port 134
- Pin Configuration 135
- RS-232 Interface Connections 136
- Modem Connection 137
- Applicator Signals 138
- Caution • Replace 140
- Isolated (External Power) 144
- Non-Isolated (Internal Print 144
- Engine Power) 144
- Fuse and Jumper Locations 145
- Specifications 147
- General Specifications 148
- Communications Specifications 149
- Other Standard Features 150
- Additional Options 150
- Agency Approvals 151
- Media Specifications 153
- Ribbon Specifications 154
- Printing Specifications 155
- Bar Codes 156
Relacionado con productos y manuales para Impresión y escaneo Zebra 110PAX4
Impresión y escaneo Zebra P110m Manual de usuario
(68 paginas)
(68 paginas)
Impresión y escaneo Zebra TTPM3 Especificaciones
(112 paginas)
(112 paginas)
Impresión y escaneo Zebra 105SL Plus Guía de usuario
(180 paginas)
(180 paginas)
Impresión y escaneo Zebra EM 220 Especificaciones
(67 paginas)
(67 paginas)
Impresión y escaneo Zebra EM 220 Manual de usuario
(30 paginas)
(30 paginas)
Impresión y escaneo Zebra S-500 Guía de usuario
(80 paginas)
(80 paginas)
Impresión y escaneo Zebra 105Se Especificaciones
(110 paginas)
(110 paginas)
Impresión y escaneo Zebra G-SERIES Guía de usuario
(58 paginas)
(58 paginas)
Impresión y escaneo Zebra RZ Series Guía de usuario
(154 paginas)
(154 paginas)
Impresión y escaneo Zebra CPCL Especificaciones
(70 paginas)
(70 paginas)
Impresión y escaneo Zebra TTPM2 Especificaciones
(140 paginas)
(140 paginas)
Impresión y escaneo Zebra R2844-Z Manual de usuario
(86 paginas)
(86 paginas)
Impresión y escaneo Zebra CPCL Especificaciones
(497 paginas)
(497 paginas)
Impresión y escaneo Zebra GK420t Guía de usuario
(22 paginas)
(22 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales