Zebra TTP2130 Especificaciones Pagina 104
- Pagina / 138
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Page Setup
Parameters Used
104
P1003640-001 TTP2100 Technical Manual 10/22/2008
Garbage, Black-mark, and Out of Paper Detection
For every step the paper is feed, the black-mark sensor is sampled to detect garbage, black-
marks or out of paper.
When the printer detects blackness is has to check if it is only garbage; if the paper gets white
again within n40 x 0.125 mm, then it is garbage and the spot is ignored. If it is still black after
n40 x 0.125 mm, it is probably a black-mark.
If the paper gets white within an additional n39-n40 plus 5 mm then it is a black-mark. The 5-
mm is a constant added to make sure that noise on the edge not will interfere with the samples.
If it at this point still is still black we have detected out of paper.
Important • Be careful about n40 and n39. If n39 – n40 is to small, then the minimum
detection area will be too little. This area should not be less than a millimeter.
Garbage range n40
Printed black mark n39
Valid black mark range (n39 – n40 + 5mm)
5 mm
Constant
Out of paper
n37 &
n38
n39
10 mm
Detection
area
- Zebra® TTP2100 1
- Technical Manual 1
- Contents 3
- Introduction 7
- Contacts 8
- Product Presentation 10
- Print and drop 11
- Print and take 11
- Controls 12
- Description 13
- Installation 15
- Installing a Paper Guide 16
- 11. Press SET 17
- 12. Press STORE 17
- Value When Used 17
- 3. Tighten the screw 18
- Calibrating the TOF Sensor 19
- Installation Considerations 20
- Quick-Fit Hubs 21
- Push down 22
- Ambient Light 24
- Paper low 25
- Connector 25
- Connecting to the Computer 26
- TTP 2130 27
- Connecting the Power 29
- Oscilloscope Setting 2A/div 30
- Self-test 31
- Making a Test Printout 32
- Installing a Printer Driver 33
- Printer Features 35
- Black-mark Settings: 36
- Operation 37
- Loading Fanfold Ticket Stock 38
- Temperature-sensitive 39
- SW96074C 39
- Wrong! Wrong! Wrong! 40
- 1. Open the printer lid 41
- Clearing Paper Jams 42
- Programming 43
- Driver Oriented 44
- ESC ! n1 45
- Select font 45
- 1B 23 Hex 48
- 27 35 decimal 48
- 1B 5A Hex 48
- 27 90 Decimal 48
- Software command syntax 49
- Barcode Commands 53
- Name Dec Hex 55
- 1B 42 57 n1 nx Hex 56
- 027 066 087 n1 nx Decimal 56
- 1B 42 43 n1 hex 56
- 27 66 67 n1 decimal 56
- 1B 7C n1 nx Hex 57
- 027 124 n1 nx Decimal 57
- 1B 62 n1...n5 Data hex 58
- 27 98 n1...n5 Data decimal 58
- 1B 73 nDataHex 58
- 27 115 n Data Decimal 58
- 1B 72 n1...n9 hex 59
- 27 114 n1...n9 decimal 59
- 1B 67 n1...n5 hex 60
- 27 103 n1...n5 decimal 60
- 1B 4C n1 Hex 60
- 27 76 n1 Decimal 60
- Print Commands 61
- Cut and Present Commands 62
- System Related Commands 64
- 1B 26 73 0A hex 67
- 27 38115 10 decimal 67
- 1B 00 Hex 67
- 27 0 Decimal 67
- Status Code Meaning 68
- 1B 05 04 hex 70
- 27 5 4 decimal 70
- 1B 05 05 hex 70
- 27 5 5 decimal 70
- 1B 05 06 hex 71
- 27 5 6 decimal 71
- 2. The printer is printing 72
- 1B 05 0C hex 74
- 27 5 12 decimal 74
- 1B 05 63 hex 74
- 27 5 99 decimal 74
- 1B 05 45 hex 75
- 27 5 69 decimal 75
- 1B 05 50 n1 Hex 76
- 27 5 80 n1 Decimal 76
- 1B 06 n1 hex 76
- 27 6 n1 decimal 76
- Font Loading 77
- Character Bitmap Data 78
- Logotypes 79
- Printing 80
- Status Reporting 81
- Default Parameter Settings 83
- Default Value 84
- Examples 84
- Summary of Parameter Settings 85
- TTP model 86
- 2110 2130 86
- Serial Interface Set-up 87
- Print Setup 88
- Fixed Document Mode 91
- Cut Position Calibration 93
- Wall Compensation (mm) 93
- TOF Sensor Mask 97
- BM Sensor 97
- Printable Area 100
- Page Setup 101
- Simple Calibration Process 102
- Parameters Used 103
- FF (Form Feed) 106
- Interface 109
- Parameter Options 110
- USB, TTP 2130 111
- Maintenance 113
- Symptom Suggested actions 114
- 1. Open the printhead 115
- Firmware 116
- FW version Change 117
- Maintenance 118
- Specifications 119
- Ticket Specifications 120
- TOF Detection 120
- Print Module 121
- Ticket Separation 121
- Presenter 121
- Electronics 122
- Text Mode 122
- Basic Character Set 123
- Miscellaneous 124
- Ordering Number List 124
- Printer Shown on 125
- Dimensions 126
- Media Holder 127
- 70W Power Supply 128
- 150W Power Supply 129
- Part Number: P1003640-001 138
- © 2008 ZIH Corp 138
Relacionado con productos y manuales para Impresión y escaneo Zebra TTP2130
Impresión y escaneo Zebra 2443 Manual de servicio
(76 paginas)
(76 paginas)
Impresión y escaneo Zebra P300i Manual de usuario
(48 paginas)
(48 paginas)
Impresión y escaneo Zebra LI 72 Guía de usuario
(86 paginas)
(86 paginas)
Impresión y escaneo Zebra 10/100 Guía de usuario
(106 paginas)
(106 paginas)
Impresión y escaneo Zebra ZE500 Guía de usuario
(170 paginas)
(170 paginas)
Impresión y escaneo Zebra GX420t Guía de usuario
(108 paginas)
(108 paginas)
Impresión y escaneo Zebra EPL2 Especificaciones
(138 paginas)
(138 paginas)
Impresión y escaneo Zebra KR203 Especificaciones
(36 paginas)
(36 paginas)
Impresión y escaneo Zebra TLP 2824 Guía de usuario
(60 paginas)
(60 paginas)
Impresión y escaneo Zebra P120i Manual de usuario
(76 paginas)
(76 paginas)
Impresión y escaneo Zebra 170PAX2 Series Guía de usuario
(100 paginas)
(100 paginas)
Impresión y escaneo Zebra LI 72 Guía de usuario
(2 paginas)
(2 paginas)
Impresión y escaneo Zebra P520 Manual de usuario
(64 paginas)
(64 paginas)
Impresión y escaneo Zebra 170PAX4 Guía de usuario
(164 paginas)
(164 paginas)
Impresión y escaneo Zebra Z6Mplus Guía de usuario
(142 paginas)
(142 paginas)
Impresión y escaneo Zebra EM 220 Manual de servicio
(53 paginas)
(53 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.060 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales