Zebra T5206R Manual de usuario Pagina 276
- Pagina / 394
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
276
Chapter 3 BATTERY CONTROL
High Volt Alert
This allows you to set the maximum voltage for determining when a “BATT
HIGH VOLT” warning occurs. When the printer receives a status from the
battery that is greater than the value of the High Volt menu, the “BATT HIGH
VOLT” warning displays on the LCD.
The range is 12.5 - 16.0 Volts, and the factory default is 16.0 Volts.
NOTE: This menu is available only when you select “Enable” in the Battery
Monitor submenu.
Low Volt Alert
This allows you to set the minimum voltage for determining when a “BATT
LOW VOLT” warning displays on the LCD. When the printer receives a status
from the battery that is less than the value of the Low Volt menu, the “BATT
LOW VOLT” warning displays on the LCD.
The range is 8.5 - 11.5 Volts, and the factory default is 9.5 Volts.
Low Volt Fault
A Low Voltage Fault occurs when the printer receives a status from the
battery that is 1.0 VDC less than the value of the Low Volt menu. In addition to
the “BATT LOW VOLT” warning, the Online Status Indicator flashes, the
printer sounds a beeping alarm, stops printing, and goes offline.
The operator can press the PAUSE key to attempt to clear the fault, but
printing cannot continue unless the battery is recharged.
NOTE: This menu is available only when you select “Enable” in the Battery
Monitor submenu.
- User’s Manual 1
- and T5000 1
- Software License Agreement 3
- Communication Notices 7
- CE Notice (European Union) 8
- Lithium Battery 10
- Trademark Acknowledgements 11
- Table of Contents 13
- 1 Introduction 19
- Corporate Offices 20
- Manual Conventions 21
- The SL5000r/T5000r 22
- Series RFID/Label Printer 22
- Standard Features 23
- Optional Features 24
- Thermal Printer Technology 25
- Thermal Consumables 26
- Setting Up The Printer 27
- Installation 29
- Parallel Interface 30
- Serial Interface 30
- Debug Interface 30
- USB Connection 30
- Status LEDs 30
- NIC Connection 31
- Coax Connection 31
- Twinax Connection 31
- 2 Operation 33
- Status and Display Indicators 34
- Control Panel Keys 35
- Control Panel Keys (cont.) 36
- Media Handling Modes 37
- Loading Media And Ribbon 38
- Loading Roll Media 39
- Media Roll 40
- Media Hanger 40
- Loading Fanfold Media 46
- Loading Ribbon 51
- Printhead 52
- Rear Ribbon 52
- Guide Roller 52
- Batch Rewind Mode 54
- Installing The Media Guide 55
- Loading Media 56
- Release 59
- Rewinder 59
- Label Peel-Off 60
- Removing The Media Guide 63
- Printing Adjustments 64
- Left Pressure Block 65
- Right Pressure Block 65
- Positioning The Media Sensors 66
- Media Guard 68
- Visible Red Beam 68
- Upper Sensor 68
- (Advanced Gap) 69
- (Advanced Notch) 70
- Sensing Different Media Types 71
- Running Auto Calibrate 72
- Running Media Profile 74
- Gap Sensing 75
- Advanced Gap Sensing 77
- Running Manual Calibrate 79
- Cleaning 80
- Platen Roller Cleaning 81
- Media Sensor Cleaning 81
- Chapter 2 Cleaning 82
- Cutter Option Cleaning 83
- 3 Configuring The Printer 85
- ↓ & ↵ 86
- Changing Printer Settings 87
- Saving A Configuration 88
- Auto Save Configuration 89
- Chapter 3 Overview 90
- Printing A Configuration 93
- Loading A Saved Configuration 93
- Menu Overview 94
- Main Menu 95
- Refer to the 99
- Chapter 3 Main Menu 100
- User’s Guide 105
- QUICK SETUP 106
- QUICK SETUP Submenus 107
- Label Width 110
- Ver Image Shift 110
- Hor Image Shift 110
- Chapter 3 QUICK SETUP 110
- Orientation 111
- Gap/Mark Sensor 112
- ↵ key with 113
- CONFIG. CONTROL 115
- CONFIG. CONTROL Submenus 116
- Name Config (1-8) 117
- Reset Cfg Names 117
- Auto Save 117
- MEDIA CONTROL 118
- MEDIA CONTROL Submenus 119
- Chapter 3 MEDIA CONTROL 122
- Auto Map Select 125
- Auto Label Width 127
- Label Wait Time 130
- Ribbon Width 133
- Display Ribbon 133
- Ribbon Low 133
- Rbn Takeup Full 133
- Ribbon Calibrate 137
- Reverse Speed 137
- Label Resolution 137
- CALIBRATE CTRL 138
- CALIBRATE CTRL Submenus 139
- Chapter 3 CALIBRATE CTRL 140
- Media Profile 140
- Sensed Distance 140
- Gap/Mark Thresh 140
- Paper Out Thresh 140
- HeadClose Action 142
- Min Calib Delta 144
- Use Label Length 144
- Threshold Range 145
- Dynamic Sensing 145
- PRINTER CONTROL 146
- PRINTER CONTROL Submenus 148
- Coax/Twinax Programmer’s 149
- Reference Manual 149
- Chapter 3 PRINTER CONTROL 150
- Host Interface 150
- Active IGP Emul 150
- Max Cache Memory 157
- Max Cached Char 157
- EMULATIONS 160
- Standard C/T Interface 161
- Simple Protocol Converter 161
- Chapter 3 EMULATIONS 162
- COAX SETUP 164
- Chapter 3 COAX SETUP 166
- TWINAX SETUP 167
- Chapter 3 TWINAX SETUP 168
- SPC COAX SETUP 169
- SPC TWINAX SETUP 170
- IPDS SETUP 171
- Chapter 3 IPDS SETUP 172
- IPDS Setup - Print IPDS Fonts 173
- TN3270 SETUP 175
- Chapter 3 TN3270 SETUP 176
- TN5250 SETUP 177
- Chapter 3 TN5250 SETUP 178
- IGP/PGL SETUP 179
- Chapter 3 IGP/PGL SETUP 180
- IGP/VGL SETUP 181
- Chapter 3 IGP/VGL SETUP 182
- P-SERIES SETUP 183
- Chapter 3 P-SERIES SETUP 184
- P-SER XQ SETUP 185
- Chapter 3 P-SER XQ SETUP 186
- SERIAL MATRIX SETUP 187
- Chapter 3 SERIAL MATRIX SETUP 188
- PROPRINTER XL SETUP 189
- Chapter 3 PROPRINTER XL SETUP 190
- EPSON FX SETUP 191
- Chapter 3 EPSON FX SETUP 192
- Emulation Submenus 193
- Chapter 3 200
- IPDS Programmer’s 206
- Programmer’s Reference Manual 206
- IMPORTANT 214
- Horizontal DPI 214
- Host Command 214
- IGP/VGL 216
- Top of Line Space 231
- Bottom of 8 LPI Line Space 231
- Bottom of 6 LPI Line Space 231
- XOH-SMO Support 236
- DIAGNOSTICS 237
- DIAGNOSTICS Submenus 238
- Chapter 3 DIAGNOSTICS 240
- Head On Time 240
- Reset Head Data 240
- Head Type 240
- Head Voltage 240
- PARALLEL PORT 241
- PARALLEL PORT Submenus 242
- Offline Process 244
- SERIAL PORT 245
- SERIAL PORT Submenus 246
- Data Protocol 247
- Chapter 3 SERIAL PORT 248
- Buffer Size in K 248
- One Char Enquiry 251
- Printer Status 251
- • ENQ/STX (see Table 9) 251
- • ENQ (see Table 10) 251
- C/T PORT 253
- USB PORT 254
- ETHERNET PORT 255
- ETHERNET ADDRESS 256
- ETHERNET ADDRESS Submenus 257
- ETHERNET PARAMS 258
- ETHERNET PARAMS Submenus 259
- WLAN ADDRESS 261
- WLAN ADDRESS Submenus 262
- WLAN PARAMS 263
- Chapter 3 WLAN PARAMS 264
- WLAN PARAMS Submenus 265
- WPA Mode 268
- WPA Cipher 268
- WPA P-Phs 268
- Reset WPA P-Phs 268
- KERBEROS PARAMS 269
- WLAN EAP 272
- Reset EAP Pswd 273
- BATTERY CONTROL 274
- Low Volt Fault 276
- PRINTER MGMT 277
- Date Submenus 278
- 4 Downloading Software 279
- Comp_Name 286
- Shared_Name 286
- Corrupt Code 287
- Using TrueType Fonts 288
- Downloading TrueType Fonts 288
- Printronix Windows Driver 289
- PGL Emulation (Online) 289
- Download Mode 290
- PTX_SETUP 292
- Labeling Applications 292
- 5 Interfaces 293
- Centronics Parallel Interface 294
- IEEE 1284 Parallel Interface 295
- Nibble Mode 296
- Byte Mode 296
- Chapter 5 USB 300
- 6 Diagnostics And 301
- Improving Processing Time 302
- Data Exchange 302
- Interfacing 303
- Controlling Print Quality 304
- Determining Printhead Wear 305
- Replacing The Printhead 306
- • Label(s) did not get 311
- • A portion of the printed 311
- • Loss of one or more 313
- • Start of image is printed 313
- • The top part of the image 313
- • Print quality is good, but 314
- • An occasional blank label 314
- Printer Alarms 316
- Fault Messages 316
- Validator 320
- • The label was 332
- • The label slipped 332
- • The label wrapped 332
- • Tear-Off or Peel 332
- • A label was 340
- • The incorrect 340
- A Specifications 345
- Appendix A 346
- Indicators And Switches 348
- Media Cutter Option 349
- Host Interfaces 349
- Environmental 350
- Physical 351
- Acoustic Specifications 351
- Maximum Page Length 351
- B Printer Options 353
- Interface Options 354
- Supplies And Accessories 355
- Genuine Printronix Media 357
- Accessories 359
- C ASCII Control Codes 361
- Appendix C 362
- D Media Cutter Installation 363
- Installing The Cutter 364
- Removing The Media Cutter 365
- E Media Cutter Tray 367
- 4. Close the media cover 369
- F Glossary 371
- Appendix F 372
- Numerics 377
- *178425-001* 394
Relacionado con productos y manuales para Impresoras De Etiquetas Zebra T5206R
Impresoras De Etiquetas Zebra Z6Mplus Guía de usuario
(166 paginas)
(166 paginas)
Impresoras De Etiquetas Zebra GX420d Guía de usuario
(106 paginas)
(106 paginas)
Impresoras De Etiquetas Zebra KR403 Especificaciones
(120 paginas)
(120 paginas)
Impresoras De Etiquetas Zebra ZP 450 Guía de usuario
(70 paginas)
(70 paginas)
Impresoras De Etiquetas Zebra 170PAX4 Guía de usuario
(156 paginas)
(156 paginas)
Impresoras De Etiquetas Zebra Stripe Guía de usuario
(78 paginas)
(78 paginas)
(20 paginas)
Impresoras De Etiquetas Zebra S600 Especificaciones
(94 paginas)
(94 paginas)
Impresoras De Etiquetas Zebra S600 Especificaciones
(168 paginas)
(168 paginas)
Impresoras De Etiquetas Zebra Stripe Información técnica
(119 paginas)
(119 paginas)
Impresoras De Etiquetas Zebra T402 Guía de usuario
(60 paginas)
(60 paginas)
Impresoras De Etiquetas Zebra DA402 Guía de usuario
(56 paginas)
(56 paginas)
Impresoras De Etiquetas Zebra A300 Especificaciones
(396 paginas)
(396 paginas)
Impresoras De Etiquetas Zebra 2684 Manual de usuario
(60 paginas)
(60 paginas)
Impresoras De Etiquetas Zebra RP4T Especificaciones
(49 paginas)
(49 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales