Zebra MP6000 Especificaciones Pagina 158
- Pagina / 210
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
5 - 4 MP6000 INTEGRATOR GUIDE
Front Panel Buttons
The three front panel user interface buttons are backlit for ease of use.
Scale Zero Button (Configurations with Scale Only)
Figure 5-3
Scale Zero Button
This button is a scale zero button and status LED that con
trols some scale operation and displays scale status.
Touch Sc
ale Zero to set the scale to zero (within +/- 0.6 lb, or +/- 0.300 kg). The LED is green and can be on,
flashing, or off. LED brightness cannot be controlled.
See Beeper and LED Indicators on page 5-20 for detailed indications.
Volume/Tone Control Button
Figure 5-4
Volume/Tone Button
This button allows user selectable settings for audible system indications.
The user can control the audible
feedback in the following situations:
•
Decoding.
•
Completion of a request (e.g., the successful decode of a bar code, and Sensormatic beep).
•
Error conditions.
•
Processing a request that takes an extended amount of time (e.g., scanning a sequence of parameter
bar codes). This audible indication informs the user that the scanner is working, and not malfunctioning.
To adjust volume and tone:
•
Press and release the Volume/Tone button to sound the current scanner beep volume level.
•
Press and release the Volume/Tone button twice within two seconds to change the scanner decode
volume.
•
Press and hold Volume/Tone for three seconds to change to another tone.
Each volume or tone change produces an audible beep when the new setting is complete. Volume and tone
wr
ap from high to low.
See Beeper and LED Indicators on page 5-20 for detailed indications.
NOTE If the decode tone is set to off, the Volume/Tone button on the MP6000 is not operational. To enable the
Volume/Tone button, set a tone option other than Off tone. Refer to the beeper and tone settings in the
MP6000 Bar Code Programming Guide (p/n 72E-172633-xx).
- INTEGRATOR GUIDE 1
- Warranty 4
- Revision History 5
- Table A 6
- TABLE OF CONTENTS 9
- Table of Contents ix 11
- Table of Contents xi 13
- ABOUT THIS GUIDE 15
- Notational Conventions 16
- Related Publications 16
- About This Guide vii 17
- FEATURES 19
- Product Overview 20
- Configurations 21
- 1 - 4 MP6000 INTEGRATOR GUIDE 22
- Table 1-1 23
- 1 - 6 MP6000 INTEGRATOR GUIDE 24
- Peripherals 26
- Features of the MP6000 27
- Left Side View 28
- View Under Platter 29
- Leveling Screws 29
- Figure 1-6 30
- Features Summary 31
- 2 - 2 MP6000 INTEGRATOR GUIDE 36
- Programming Management Tools 37
- Connecting a USB Interface 38
- USB Host Parameters 40
- * IBM Table-top USB 41
- USB Device Type (continued) 42
- Figure 2-3 47
- Table 2-3 47
- (see parameter 47
- page 2-32 47
- Connect MP6000 to RS-232 Host 48
- RS-232 Parameters 49
- RS-232 Host Parameters 50
- Table 2-7 52
- Table 2-8 53
- RS-232 Host Types 54
- *Standard RS-232 55
- RS-232 Host Types (continued) 56
- RS-232 Host -NCR Variant 64
- Parameter # 1246 66
- Third Party Scale 71
- Parameter # 1294 71
- Third Party Scale (continued) 72
- Third Party Scale LED Pin 73
- Parameter # 1295 73
- *Active High 74
- Third Party Scale Zero Pin 75
- Parameter # 1296 75
- IBM RS-485 Host Parameters 78
- *None Selected 79
- RS-232 AUX 1 87
- Scale Display Port 87
- RS-232 AUX 2 88
- Checkpoint Interlock 88
- AUX A-B (Stacked USB) 88
- Table 2-15 89
- Table 2-16 89
- INSTALLATION 91
- Site Preparation 92
- Grounding 93
- Liquid Spills and Moisture 94
- Vertical Clearance 94
- Counter Cutout 95
- Ergonomics 95
- Installing Components 96
- Unpacking MP6000 Equipment 97
- Pre-Installation Notes 98
- Required Tools 99
- Secure in Place 101
- Install the Scale Display 102
- Getting Started 104
- Installing 105
- Inserting the Scan Module 109
- Connecting the USB Cable 110
- Figure 3-25 112
- Figure 3-24 112
- Install the MP6000 /Scale 115
- Figure 3-30 116
- Figure 3-31 116
- Figure 3-32 117
- Figure 3-33 117
- Optional leveling screw kit 117
- MX301-SR00004ZZWR 117
- Figure 3-34 118
- Figure 3-35 118
- Figure 3-36 119
- Figure 3-37 119
- MX301-SR00004ZZWR or 119
- MX302-SR00004ZZWR 119
- Figure 3-38 120
- Figure 3-39 120
- 11.50 in 121
- 292.2 mm 121
- 20.0 in 121
- 506.9 mm 121
- Install Sensormatic Coils 124
- Install Checkpoint Antenna 127
- Figure 3-48 128
- Figure 3-49 128
- Installing the Mounting Frame 129
- WITH A SCALE ONLY) 131
- Scale Configurations 132
- Identifying Firmware Version 132
- Legal Scale Dampening Filter 134
- Step 4 - Calibration at LOAD 135
- 4 - 6 MP6000 INTEGRATOR GUIDE 136
- Calibration Success 137
- Calibration Failure 137
- Verification Test 138
- Table 4-5 139
- Table 4-4 139
- Audit Tallies 141
- * Kilograms 143
- Legal Scale Units (continued) 144
- Scale Display Configuration 145
- Parameter # 986 145
- Parameter # 996 147
- * Low Vibration Sensitivity 148
- Parameter # 996 (continued) 149
- Table 4-6 151
- Overview 155
- Controls and Indicators 156
- OPERATING THE SCANNER 5 - 3 157
- Volume/Tone Control Button 158
- Soft Reset Buttons 159
- Single Interval Range Scales 160
- Dual Interval Range Scales 160
- OPERATING THE SCANNER 5 - 7 161
- 5 - 8 MP6000 INTEGRATOR GUIDE 162
- Scan Windows 163
- Operating Modes 164
- Programming the MP6000 164
- USB Staging Flash Drive 165
- Flash DrivesFlash Drives 166
- Loading Cloning Files 167
- Scanning 169
- Weighing Items 170
- Supported EAS Controllers 171
- Sensormatic EAS Hard Tags 172
- OPERATING THE SCANNER 5 - 19 173
- Beeper and LED Conditions 174
- OPERATING THE SCANNER 5 - 21 175
- Table 5-1 176
- OPERATING THE SCANNER 5 - 23 177
- CHAPTER 6 123SCAN2 179
- Requirements 180
- APPENDIX A MAINTENANCE 181
- TROUBLESHOOTING, AND 181
- ERROR CODES 181
- Troubleshooting 182
- Troubleshooting Assistance 183
- A - 4 MP6000 INTEGRATOR GUIDE 184
- Table A-1 185
- Scale Warning Codes 186
- A - 8 MP6000 INTEGRATOR GUIDE 188
- Technical Specifications 189
- B - 2 MP6000 INTEGRATOR GUIDE 190
- Table B-1 191
- B - 4 MP6000 INTEGRATOR GUIDE 192
- APPENDIX C HOST INTERFACE 193
- CHARACTER SETS 193
- RS-232 Character Sets 194
- Table C-1 195
- C - 4 MP6000 INTEGRATOR GUIDE 196
- C - 6 MP6000 INTEGRATOR GUIDE 198
- Table D-1 199
- D - 2 MP6000 INTEGRATOR GUIDE 200
- APPENDIX E COMMUNICATION 201
- PROTOCOLS 201
- E - 2 MP6000 INTEGRATOR GUIDE 202
- Numerics 203
- Index - 3 205
- Tell Us What You Think 207
© 2020, manymanuals.es. Todos los derechos reservados | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales