Zebra ZM400 Guía de usuario Pagina 99
- Pagina / 116
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
99
Hardware Troubleshooting
Troubleshooting the 10/100 PS
02/01/2011 ZebraNet
®
10/100 Print Server User Guide 47619L-006 Rev. A
3. Flashing red indicates the Power On Self-Test (POST) is in progress.
• If an active network cable is connected and the LED is solid red for more than 30 seconds,
the 10/100 PS has failed the POST. If the failure is not severe, the 10/100 PS attempts to
print a configuration label on the printer. A failed POST may be a connection to a
malfunctioning 10/100 PS device.
1. Turn the printer off (O), wait 10 seconds, then turn the printer on (I).
2. If the 10/100 PS still fails the POST, continue below.
3. The 10/100 PS has a hardware problem that can be fixed only by replacing or
returning the unit. Contact Repair for repair or replacement information.
• If the LED is alternately flashing red and green for longer than 2 minutes, the 10/100 PS
is in firmware-download mode. This means it is waiting for new firmware data to be sent
before it continues normal functioning. Perform the following:
1. If the 10/100 PS was purposely put into firmware-download mode, finish the
download with the proper update utility. Visit the Zebra Web site at http://www.zebra.com
to download this utility.
2. If the 10/100PS was not purposely put into firmware-download mode or if you wish
to exit this mode, default the unit. Follow the instructions in 10/100 PS Status Indicator
on page 98.
3. Contact Technical Support for additional help.
10/100 PS Network Status/Activity Indicator
A bi-color Status/Activity LED indicates network speed, established link, and network
activity.
• If the LED is off, no link was established.
• If the LED is solid green, a 100BASE-T link is established.
• If the LED is flashing green, a 100BASE-T link is established and network activity has
been detected.
• If the LED is solid orange, a 10BASE-T link is established.
• If the LED is flashing orange, a 10BASE-T link was established and network activity has
been detected.
Network activity detected by this LED does not mean the activity is data for the print server.
The activity is all activity on the network seen on the 10/100 PS.
- ZebraNet® 1
- 10/100 Print Server 1
- User Guide 1
- Contents 3
- Who Should Use This Document 8
- Contacts 9
- Document Conventions 10
- About This Document 11
- Related Documents 12
- Introduction 13
- Overview 14
- Requirements 14
- Hardware 15
- Firmware 16
- PN XXXXX 17
- Compatibility 18
- Installation Types 19
- General Specifications 20
- Installation 21
- External 10/100 PS 22
- Illustration 23
- Installation Instructions 24
- DPI Inches mm 25
- Internal 10/100 PS 26
- Getting Started 27
- Before You Begin 28
- Assigning an IP Address 30
- IP RESOLUTION 31
- Static Route 32
- Gleaning 33
- ZebraLink Alerts 34
- Alert Type Error Condition 35
- Using ZebraNet Bridge 36
- Using WebView 36
- Alert Setup 37
- Add Alert Message 37
- Save Printer Setting 38
- Save Current Configuration 38
- Figure 9 • Browser View 40
- Print Server Settings 41
- Figure 11 • Access Settings 42
- Enabling Protocols 43
- Print Server 44
- Enabled Protocols 45
- Submit Changes 45
- Defaulting the 10/100 PS 46
- Using the Test Button 47
- Printing Configurations 49
- Configuring the Print Queue 50
- System V Queue Installation 51
- Using Printing Protocols 53
- 1. Open a browser 54
- 12.3.4.123, you would type: 55
- ZebraLink WebView 57
- Home Page 58
- Open a Web browser 59
- The Printer Home Page opens 59
- Figure 16 • Printer Home Page 59
- View Printer Configuration 60
- If... Then 61
- Home link 61
- Print Label 61
- Table 3 • Menu Options 63
- General Setup 63
- Serial Communications Setup 63
- Network Communications 64
- Print Listings on Label 64
- Media Setup 65
- Calibration 65
- ZPL Control 66
- Advanced Setup 66
- Directory Listing 67
- Printer Controls 68
- Figure 20 • Printer Controls 69
- Zebra BASIC Interpreter (ZBI) 70
- 10/100 PS Features 72
- Figure 22 • Printer Home Page 73
- Use this feature to set the 77
- Use this 77
- Print Server Status 81
- View Port Status 82
- Reset Print Server 83
- Click Network Configuration 87
- Figure 31 opens 87
- TCP/IP Settings 89
- Network Configuration 90
- Click TCP/IP Settings 91
- Figure 35 opens 91
- Control Panel 93
- Control Panel Menu Options 94
- Hardware Troubleshooting 97
- Troubleshooting the 10/100 PS 98
- Unable to Print 100
- Start > Run 101
- Open text box, type: cmd 101
- Unable to Configure Device 102
- Frequently Asked Questions 103
- Glossary 107
- 02/01/2011 ZebraNet 111
- 47619L-006 Rev. A ZebraNet 112
Relacionado con productos y manuales para Impresoras De Etiquetas Zebra ZM400
Impresoras De Etiquetas Zebra ZD500 Guía de usuario
(160 paginas)
(160 paginas)
Impresoras De Etiquetas Zebra ZT230 Guía de usuario
(18 paginas)
(18 paginas)
Impresoras De Etiquetas Zebra GC420d Guía de usuario
(100 paginas)
(100 paginas)
Impresoras De Etiquetas Zebra GX430D Guía de usuario
(128 paginas)
(128 paginas)
Impresoras De Etiquetas Zebra T5206R Manual de usuario
(394 paginas)
(394 paginas)
Impresoras De Etiquetas Zebra Z6Mplus Guía de usuario
(166 paginas)
(166 paginas)
Impresoras De Etiquetas Zebra GX420d Guía de usuario
(106 paginas)
(106 paginas)
Impresoras De Etiquetas Zebra KR403 Especificaciones
(120 paginas)
(120 paginas)
Impresoras De Etiquetas Zebra ZP 450 Guía de usuario
(70 paginas)
(70 paginas)
Impresoras De Etiquetas Zebra 170PAX4 Guía de usuario
(156 paginas)
(156 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.120 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales