Zebra RW SERIES Especificaciones descargar pdf (Pagina 56)

RMAN-RWS-001 rev. B • RW Series Repair Procedures • 2-56 •

Remove the Connector Door

1. Pull the Connector Door away from the lower housing

Install the Connector Door

1. Press the Connector Door into place on the lower housing. Ensure that the top

ap of the Connector Door sits properly on the lower housing as shown.

Re-assemble the Keypad and Housing Assembly

1. Re-assemble the Keypad and Housing Assembly to the Printer, referring to the

procedure for RK1793-008/RK18280-1 as needed for more details.

Door, Rubber, RW 420

p/n BA17089-1

1 2 ... 51 52 53 54 55 56 57 58 59 60 61 ... 113 114

RW Series 1
RMAN-RWS-001 rev.B • -ii • 2
Contents 3
RMAN-RWS-001 rev.B • -iv • 4
Description 5
Operating Modes 5
Printing Technology 5
Communications 5
User Guide 5
Diagnostic Tools 9
Diagnostic Label Printout 9
Label Vista™ 9
Factory Technical Support 9
Printing a Diagnostic Label 10
Creating a Conﬁguration Label 10
Sample Conﬁguration Label 10
Introduction to Label Vista™ 13
Starting Label Vista 13
Equipment Required 14
Running The Software 14
Tools and Supplies 15
Handling 15
Storage and Handling 15
• 2-16 • 16
Unplug the Bar 16
Sense Cable 16
Peel the old Bar Sense 17
Cable away from the 17
• 2-20 • 20
into place as 20
• 2-22 • 22
Installing the Media Assembly 23
CPU CONNECTIONS 24
Removing the Printhead 26
Installing the Printhead 27
Removing the Motor 30
• 2-32 • 32
• 2-34 • 34
• 2-36 • 36
Unplug LCD and Keypad ﬂex 36
Separate the Assemblies 37
• 2-38 • 38
Remove and retain Card 38
Reader Assembly and 38
Keypad and Housing Assembly 40
Remove the Card Reader 41
Install the Card Reader 42
Kit p/n Description 45
RK17393-029 Radio 802.11g Kit 45
Remove the Radio Assembly 46
• 2-48 • 48
Replace the Belt Clip 52
Clip, D-Ring 53
Removing the “D” Rings 54
Installing the “D” Rings 54
Remove the Connector Door 56
Install the Connector Door 56
• 2-60 • 60
Install the Base Plate 62
Finish the Installation 62
Unplug the 63
Bar Sense 63
Cable from J2 63
• 2-64 • 64
10. Calibrate the Sensors 66
• 2-72 • 72
Changing the Media Core Size 73
• 2-74 • 74
• 2-78 • 78
• 2-84 • 84
802.11b Antenna PCB Assembly 87
Bracket, Radio (Card version 87
• 2-88 • 88
Radio PCB Assembly 88
• 2-92 • 92
Install the Upper Housing 96
Removing the Controller Board 98
Controller Board 100
Test the Printer 101
IN THE USA IN EUROPE 103
RW Series Accessories 104
PCC Example 106
RW 420 Accessory Kits 107
RW 420 Replacement Kits 107
REPLACEMENT 109
AK17463-005 109
ITEM PART # DESCRIPTION 110
RW 220 Accessory Kits 111
RW 220 Replacement Kits 112
12 3 5 8 113

Comentarios a estos manuales

Sin comentarios

Zebra RW SERIES Especificaciones Pagina 56

Comentarios a estos manuales

Relacionado con productos y manuales para Impresión y escaneo Zebra RW SERIES