Zebra RW SERIES Especificaciones Pagina 59
- Pagina / 114
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
• 2-59 • RMAN-RWS-001 rev. B • RW Series Repair Procedures
Unplug the Communications Cable
1. If you have a communications cable plugged into the RS232 port on the Vehicle
Cradle, un-plug it.
Remove the Cradle from the RAM Mount
1. If the Vehicle Cradle is attached to the optional RAM Mount, remove it and
retain the mounting hardware.
Remove the Bottom Plate
1. Remove and retain the (7) screws from the Plate, RW4 Cradle RAM Mount.
(Marked “A” on illustration.)
2. Lower the Plate away from the PCB. Note that it is still attached to the PCB by
the ground strap.
Remove the PCB
1. Remove the power cable from the PCB. It may be necessary to remove the
cable clamps holding the Power Cable in place on the Upper Housing.
2. Unplug the ex circuit from J2 on the PCB to the display pad on the Upper
Housing.
3. Remove and retain the (5) Screws from the PCB. (Marked “B” on illustration.)
4. Remove the PCB assembly from the upper housing. Note that it is still attached
to the Plate by the ground strap.
5. Remove the screw and nut from the RS232 connector on the PCB that retains
the Ground Strap on the PCB. Remove and retain the Plate and the attached
Grounding Strap.
Install the replacement PCB
1. Secure the ground strap, still attached to the Plate, RW4 Cradle RAM Mount
to the RS232 connector on the replacement PCB using the screw and hex nut
removed in the rst step.
2. Secure the PCB to the Upper Housing of the Vehicle Cradle with (5) Screws
retained in the previous step..
3. Plug the Flex Circuit from the Upper Housing into the PCB.
4. Plug the power cable into the PCB
Install the Base Plate
1. Secure the Plate, RW4 Cradle RAM Mount to the Upper Housing with the (7)
screws retained from the rst step.
Finish the Installation
1. Re-secure any cable clamps you removed during the disassembly procedure.
Ensure the power cable is routed correctly for your installation.
2. If you removed a communications cable from the Cradle, reinstall it.
3. If the Cradle was attached to a RAM Mount, re-secure it with the retained
hardware.
- RW Series 1
- RMAN-RWS-001 rev.B • -ii • 2
- Contents 3
- RMAN-RWS-001 rev.B • -iv • 4
- Description 5
- Operating Modes 5
- Printing Technology 5
- Communications 5
- User Guide 5
- Diagnostic Tools 9
- Diagnostic Label Printout 9
- Label Vista™ 9
- Factory Technical Support 9
- Printing a Diagnostic Label 10
- Creating a Configuration Label 10
- Sample Configuration Label 10
- Introduction to Label Vista™ 13
- Starting Label Vista 13
- Equipment Required 14
- Running The Software 14
- Tools and Supplies 15
- Handling 15
- Storage and Handling 15
- • 2-16 • 16
- Unplug the Bar 16
- Sense Cable 16
- Peel the old Bar Sense 17
- Cable away from the 17
- • 2-20 • 20
- into place as 20
- • 2-22 • 22
- Installing the Media Assembly 23
- CPU CONNECTIONS 24
- Removing the Printhead 26
- Installing the Printhead 27
- Removing the Motor 30
- • 2-32 • 32
- • 2-34 • 34
- • 2-36 • 36
- Unplug LCD and Keypad flex 36
- Separate the Assemblies 37
- • 2-38 • 38
- Remove and retain Card 38
- Reader Assembly and 38
- Keypad and Housing Assembly 40
- Remove the Card Reader 41
- Install the Card Reader 42
- Kit p/n Description 45
- RK17393-029 Radio 802.11g Kit 45
- Remove the Radio Assembly 46
- • 2-48 • 48
- Replace the Belt Clip 52
- Clip, D-Ring 53
- Removing the “D” Rings 54
- Installing the “D” Rings 54
- Remove the Connector Door 56
- Install the Connector Door 56
- • 2-60 • 60
- Install the Base Plate 62
- Finish the Installation 62
- Unplug the 63
- Bar Sense 63
- Cable from J2 63
- • 2-64 • 64
- 10. Calibrate the Sensors 66
- • 2-72 • 72
- Changing the Media Core Size 73
- • 2-74 • 74
- • 2-78 • 78
- • 2-84 • 84
- 802.11b Antenna PCB Assembly 87
- Bracket, Radio (Card version 87
- • 2-88 • 88
- Radio PCB Assembly 88
- • 2-92 • 92
- Install the Upper Housing 96
- Removing the Controller Board 98
- Controller Board 100
- Test the Printer 101
- IN THE USA IN EUROPE 103
- RW Series Accessories 104
- PCC Example 106
- RW 420 Accessory Kits 107
- RW 420 Replacement Kits 107
- REPLACEMENT 109
- AK17463-005 109
- ITEM PART # DESCRIPTION 110
- RW 220 Accessory Kits 111
- RW 220 Replacement Kits 112
- 12 3 5 8 113
Relacionado con productos y manuales para Impresión y escaneo Zebra RW SERIES
Impresión y escaneo Zebra P430i Manual de usuario
(68 paginas)
(68 paginas)
Impresión y escaneo Zebra 3742 Manual de servicio
(56 paginas)
(56 paginas)
Impresión y escaneo Zebra QLn220 Manual de usuario
(12 paginas)
(12 paginas)
Impresión y escaneo Zebra RP4T Manual de usuario
(6 paginas)
(6 paginas)
Impresión y escaneo Zebra 10/100 Manual de usuario
(116 paginas)
(116 paginas)
Impresión y escaneo Zebra P320i Guía de usuario
(66 paginas)
(66 paginas)
Impresión y escaneo Zebra EPL2 Especificaciones
(248 paginas)
(248 paginas)
Impresión y escaneo Zebra EM220II Manual de usuario
(37 paginas)
(37 paginas)
Impresión y escaneo Zebra 105SL Plus Guía de usuario
(174 paginas)
(174 paginas)
Impresión y escaneo Zebra TTP2130 Especificaciones
(138 paginas)
(138 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales